Makita DVC864LZ - Инструкция по эксплуатации - Страница 12

12 ENGLISH

WIRELESS ACTIVATION 

FUNCTION

What you can do with the wireless 

activation function

The wireless activation function enables clean and 

comfortable operation. By connecting a supported tool 

to the cleaner, you can run the cleaner automatically 

along with the switch operation of the tool.

► 

Fig.9

NOTICE:

Be sure to refer to the instruction man-

ual of the tool when using the cleaner with wire-

less activation function.

NOTICE:

Do not disassemble or tamper with the 

wireless unit.

NOTICE:

Always close the lid of the wireless unit 

in the tool when operating or storage.

NOTICE:

Do not remove the wireless unit from 

the tool while the power is being supplied to the 

tool.

 Doing so may cause a malfunction of the wire-

less unit.

NOTICE:

Do not press the wireless activation 

button too hard and/or press the button with an 

object with a sharp edge.

NOTE:

 Wireless activation needs Makita tools 

equipped with the wireless unit.

NOTE:

 Prior to the initial use of the wireless activation 

function with each tool, the tool registration is required. 

Once the registration is finished with the tool, the 

re-registration is not required unless it is cancelled.

NOTE:

 Before registration, be sure to the wireless 

unit is properly inserted into the tool.

NOTE:

 One cleaner can register up to 10 tools. If 

more than 10 tools are registered to the cleaner, the 

tool registered earliest will be cancelled automatically.

NOTE:

 The position of the wireless activation button 

varies depending on the tool.

NOTE:

 The cleaner also starts by pressing the power 

button when the stand-by switch is set to "AUTO".

However the power button will not actuate when the 

wireless activation function is used.

Tool registration for the cleaner

NOTE:

 A Makita tool supporting the wireless activa

-

tion function is required for the tool registration.

NOTE:

 Finish installing the wireless unit to the tool 

before starting the tool registration.

NOTE:

 During the tool registration, do not pull the 

switch trigger on the tool or turn on the power switch 

on the cleaner.

NOTE:

 Refer to the instruction manual of the tool, too.

If you wish to activate the cleaner along with the 

switch operation of the tool, finish the tool registration 

beforehand.

1.

  Install the batteries to the cleaner and the tool.

2.

  Set the stand-by switch on the cleaner to "AUTO".

► 

Fig.10:

1.

 Stand-by switch

3.

Press the wireless activation button on the cleaner 

for 3 seconds until the wireless activation lamp blinks in 

green. And then press the wireless activation button on 

the tool in the same way.

► 

Fig.11:

1.

 Wireless activation button 

2.

 Wireless 

activation lamp

If the cleaner and the tool are linked successfully, the 

wireless activation lamps will light up in green for 2 

seconds and start blinking in blue.

NOTE:

 The wireless activation lamps finish blinking 

in green after 20 seconds elapsed. Press the wireless 

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless 

activation lamp does not blink in green, push the wire-

less activation button briefly and hold it down again.

NOTE:

 When performing two or more tool registration 

for the cleaner, finish the tool registration one by one.

Starting the wireless activation 

function

NOTE:

 Finish the tool registration for the cleaner for 

wireless activation.

NOTE:

 Always place the cleaner so that you can see 

the status of the wireless activation lamp.

NOTE:

 Refer to the instruction manual of the tool, too.

After registering a tool to the cleaner, the cleaner will auto-

matically runs along with the switch operation of the tool.

1.

  Install the wireless unit to the tool.

2.

Connect the hose of the cleaner with the tool.

► 

Fig.12

3.

  Set the stand-by switch on the cleaner to "AUTO".

► 

Fig.13:

1.

 Stand-by switch

4.

Push the wireless activation button on the tool 

briefly. The wireless activation lamp will blink in blue.

► 

Fig.14:

1.

 Wireless activation button 

2.

 Wireless 

activation lamp

5.

  Pull the switch trigger of the tool. Check if the cleaner 

runs while the switch trigger on the tool is being pulled.
To stop the wireless activation, push the wireless activa-

tion button on the tool, or set the stand-by switch on the 

cleaner to "I" or "O".

NOTE:

 The wireless activation lamp on the tool will stop 

blinking in blue when there is no operation for 2 hours. In 

this case, set the stand-by switch on the cleaner to "AUTO" 

and press the wireless activation button on the tool again.

NOTE:

 The cleaner starts/stops with a delay. There is a time 

lag when the cleaner detects a switch operation of the tool.

NOTE:

 The transmission distance of the wireless unit may 

vary depending on the location and surrounding circumstances.

NOTE:

 When two or more tools are registered to one 

cleaner, the cleaner may start running even if you 

don't pull the switch trigger because other user is 

using the wireless activation function.