Makita DVC864LZ - Инструкция по эксплуатации - Страница 11

11 ENGLISH

Indicator lamps

Remaining 

capacity

Lighted

Off

Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the 

battery.

The battery 

may have

malfunctioned.

NOTE:

 Depending on the conditions of use and the 

ambient temperature, the indication may differ slightly 

from the actual capacity.

Indicating the remaining battery 

capacity

► 

Fig.4:

1.

 Battery indicator 

2.

 Check button 

3.

 Stand-by switch

► 

Fig.5

Press the check button to indicate the remaining battery 

capacities. The battery indicators correspond to each 

battery.

Battery indicator status

Remaining 

battery 

capacity

On

Off

Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the 

battery

NOTE:

 During the cleaner turned on with the stand-by 

switch set to "AUTO", the battery indicator does not 

work.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the 

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is 

placed under one of the following conditions:

Overload protection

When the tool is operated in a manner that causes it to 

draw an abnormally high current, the tool automatically 

stops without any indication. In this situation, turn the 

tool off and stop the application that caused the tool to 

become overloaded. Then turn the tool on to restart.

Overheat protection

 On

 Blinking

When the tool is overheated, the tool stops automatically, and 

the battery indicator blinks about 60 seconds. In this situa

-

tion, let the tool cool down before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops 

automatically. If the product does not operate even 

when the switches are operated, remove the batteries 

from the tool and charge the batteries.

Switch action

► 

Fig.6:

1.

 Stand-by switch 

2.

 Power button 

3.

 Suction 

force adjusting knob

To start the cleaner:
1.  Set the stand-by switch to the "I" side. The cleaner 

gets into stand-by state.

2.  Press the power button.

To make the cleaner get into stand-by mode, press the 

power button again.

To turn off the cleaner, set the stand-by switch to the "O" side.
The suction power can be adjusted according to your 

work need.

Suction power can be increased by turning the suction force 

adjusting knob from the 

 symbol to the 

 symbol.

NOTICE:

 Always set the stand-by switch to the "O" 

side when not using the cleaner for long time. The 

cleaner consumes power during stand-by state.

Locking or unlocking the caster

► 

Fig.7:

1.

 Caster 

2.

 Stopper lever 

3.

 FREE position 

4.

 LOCK position

Locking the caster is convenient when storing the cleaner, 

stopping the work on the way and keeping the cleaner still.

To operate the stopper, move it by hand.

To lock the caster with a stopper, lower the stopper 

lever and the caster no longer will rotate. To release the 

caster from the locked position, raise the stopper lever.

NOTE:

When moving the cleaner, make sure that the 

caster is unlocked. Moving the cleaner with the caster 

in the locked position may cause damage to the caster.

Carriage handle

When carrying the cleaner, carry it by holding the han

-

dle on the head. The handle is retractable at the head 

when not in use.

► 

Fig.8