ARDESTOBright SWMG-7120W - Инструкция по эксплуатации - Страница 53

EN

USING THE DETERGENT DRAWER

Make sure that no garments are nipped between the door and  

        the seal.

It is recommended to use low foaming powder for all washing 

temperature programs.

1.  Open the drawer and add adequate detergent into main wash 

compartment marked «

1. Open the drawer and add adequate detergent into main wash compartment marked “     

” or “  

 ”.

2. Add the fabric softener into compartment marked “       ” or “     ” .

    Do not exceed the maximum level mark.

3. Close the drawer.

How to use washer

Use process

Using the detergent drawer

The right amount to dispenser will depend on the following:

The quantity of laundry

The soiling level of the laundry

- 

Lightly soiled

   No visible dirt or stains. Possibly

slight body odour.

- 

Normally soiled

Visibly dirty and/or just a few slight

stains.

- 

Heavily soiled

Visible dirt and stains and/or dried on

soiling.

The water hardness level.

It is recommended to use low foaming powder for all washing temperature programs.

Washing steps

1.Turn on the water tap, and connect the power.

2.Open the door, and put the cloth into the drum one by one.

3.Close the door, and put suitable amount of  detergent and fabric softener into the

   dispenser, then close the drawer.

4.Choose a program you need .

5.Press “ Start/Pause” button to start the washing machine.

6.When the cycle is finished, there is a warning tone sound.

12

11

When the machine is started , the door lock is locked 

When the temperature inside the durm is above 60

℃

, the door lock is locked. 

When the water is above a certain level, the door lock is locked. 

When the washing cycle is finished, the door lock is unlocked.

How to use washer

Use process

Door lock

Important:

Do not try to open the door when the washing cycle is not finished or power supply is cut off

during the washing cycle, because the temperature may be high and you may be scalded.

Use process

Cleanness and Maintenance

Disconnect the machine from the mains electricity supply and withdraw the plug from

the socket before cleaning the machine.

The washing machine must not be hosed down.

Cleaning the exterior 

Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a well wrung-out

cloth. Wipe dry with a soft cloth.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.

These might damage plastic surfaces and other components because of the chemicals

they contain.

The washing drum

Clean the drum every 3 months by using the “Drum Clean” programme.

Cleaning the drawer

Remove detergent residues regularly.

Clear

the

drawer

following

these

:

Pull out the

drawer until a resistance is felt. 

Press

down the release catch and at the same time

pull the drawer right out of

the machine.

Remove the siphon from

compartment 

and

clean

it

.

Clean the 

dispenser

using a brush and warm water.

When washing cycle is finished, the machine will change into standby mode.

And the machine will be sleeping after 10 minutes without any control on the 

control panel.

Main wash compartment

Fabric softener compartment

Pre-wash compartment

The machine is fitted with a balance control device, which ensures the machine is stable

during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed

in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen

several times before the unbalance disappears and normal spinning can resume. If, after

about 20 minutes, the laundry is still not evenly distributed in the drum, the machine will not

spin. In this case, redistributed the load manually and reselect the spin program. 

» оr «

1. Open the drawer and add adequate detergent into main wash compartment marked “     

” or “  

 ”.

2. Add the fabric softener into compartment marked “       ” or “     ” .

    Do not exceed the maximum level mark.

3. Close the drawer.

How to use washer

Use process

Using the detergent drawer

The right amount to dispenser will depend on the following:

The quantity of laundry

The soiling level of the laundry

- 

Lightly soiled

   No visible dirt or stains. Possibly

slight body odour.

- 

Normally soiled

Visibly dirty and/or just a few slight

stains.

- 

Heavily soiled

Visible dirt and stains and/or dried on

soiling.

The water hardness level.

It is recommended to use low foaming powder for all washing temperature programs.

Washing steps

1.Turn on the water tap, and connect the power.

2.Open the door, and put the cloth into the drum one by one.

3.Close the door, and put suitable amount of  detergent and fabric softener into the

   dispenser, then close the drawer.

4.Choose a program you need .

5.Press “ Start/Pause” button to start the washing machine.

6.When the cycle is finished, there is a warning tone sound.

12

11

When the machine is started , the door lock is locked 

When the temperature inside the durm is above 60

℃

, the door lock is locked. 

When the water is above a certain level, the door lock is locked. 

When the washing cycle is finished, the door lock is unlocked.

How to use washer

Use process

Door lock

Important:

Do not try to open the door when the washing cycle is not finished or power supply is cut off

during the washing cycle, because the temperature may be high and you may be scalded.

Use process

Cleanness and Maintenance

Disconnect the machine from the mains electricity supply and withdraw the plug from

the socket before cleaning the machine.

The washing machine must not be hosed down.

Cleaning the exterior 

Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a well wrung-out

cloth. Wipe dry with a soft cloth.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.

These might damage plastic surfaces and other components because of the chemicals

they contain.

The washing drum

Clean the drum every 3 months by using the “Drum Clean” programme.

Cleaning the drawer

Remove detergent residues regularly.

Clear

the

drawer

following

these

:

Pull out the

drawer until a resistance is felt. 

Press

down the release catch and at the same time

pull the drawer right out of

the machine.

Remove the siphon from

compartment 

and

clean

it

.

Clean the 

dispenser

using a brush and warm water.

When washing cycle is finished, the machine will change into standby mode.

And the machine will be sleeping after 10 minutes without any control on the 

control panel.

Main wash compartment

Fabric softener compartment

Pre-wash compartment

The machine is fitted with a balance control device, which ensures the machine is stable

during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed

in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen

several times before the unbalance disappears and normal spinning can resume. If, after

about 20 minutes, the laundry is still not evenly distributed in the drum, the machine will not

spin. In this case, redistributed the load manually and reselect the spin program. 

».

2.  Add the fabric softener into compartment marked «

1. Open the drawer and add adequate detergent into main wash compartment marked “     

” or “  

 ”.

2. Add the fabric softener into compartment marked “       ” or “     ” .

    Do not exceed the maximum level mark.

3. Close the drawer.

How to use washer

Use process

Using the detergent drawer

The right amount to dispenser will depend on the following:

The quantity of laundry

The soiling level of the laundry

- 

Lightly soiled

   No visible dirt or stains. Possibly

slight body odour.

- 

Normally soiled

Visibly dirty and/or just a few slight

stains.

- 

Heavily soiled

Visible dirt and stains and/or dried on

soiling.

The water hardness level.

It is recommended to use low foaming powder for all washing temperature programs.

Washing steps

1.Turn on the water tap, and connect the power.

2.Open the door, and put the cloth into the drum one by one.

3.Close the door, and put suitable amount of  detergent and fabric softener into the

   dispenser, then close the drawer.

4.Choose a program you need .

5.Press “ Start/Pause” button to start the washing machine.

6.When the cycle is finished, there is a warning tone sound.

12

11

When the machine is started , the door lock is locked 

When the temperature inside the durm is above 60

℃

, the door lock is locked. 

When the water is above a certain level, the door lock is locked. 

When the washing cycle is finished, the door lock is unlocked.

How to use washer

Use process

Door lock

Important:

Do not try to open the door when the washing cycle is not finished or power supply is cut off

during the washing cycle, because the temperature may be high and you may be scalded.

Use process

Cleanness and Maintenance

Disconnect the machine from the mains electricity supply and withdraw the plug from

the socket before cleaning the machine.

The washing machine must not be hosed down.

Cleaning the exterior 

Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a well wrung-out

cloth. Wipe dry with a soft cloth.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.

These might damage plastic surfaces and other components because of the chemicals

they contain.

The washing drum

Clean the drum every 3 months by using the “Drum Clean” programme.

Cleaning the drawer

Remove detergent residues regularly.

Clear

the

drawer

following

these

:

Pull out the

drawer until a resistance is felt. 

Press

down the release catch and at the same time

pull the drawer right out of

the machine.

Remove the siphon from

compartment 

and

clean

it

.

Clean the 

dispenser

using a brush and warm water.

When washing cycle is finished, the machine will change into standby mode.

And the machine will be sleeping after 10 minutes without any control on the 

control panel.

Main wash compartment

Fabric softener compartment

Pre-wash compartment

The machine is fitted with a balance control device, which ensures the machine is stable

during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed

in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen

several times before the unbalance disappears and normal spinning can resume. If, after

about 20 minutes, the laundry is still not evenly distributed in the drum, the machine will not

spin. In this case, redistributed the load manually and reselect the spin program. 

» оr «

1. Open the drawer and add adequate detergent into main wash compartment marked “     

” or “  

 ”.

2. Add the fabric softener into compartment marked “       ” or “     ” .

    Do not exceed the maximum level mark.

3. Close the drawer.

How to use washer

Use process

Using the detergent drawer

The right amount to dispenser will depend on the following:

The quantity of laundry

The soiling level of the laundry

- 

Lightly soiled

   No visible dirt or stains. Possibly

slight body odour.

- 

Normally soiled

Visibly dirty and/or just a few slight

stains.

- 

Heavily soiled

Visible dirt and stains and/or dried on

soiling.

The water hardness level.

It is recommended to use low foaming powder for all washing temperature programs.

Washing steps

1.Turn on the water tap, and connect the power.

2.Open the door, and put the cloth into the drum one by one.

3.Close the door, and put suitable amount of  detergent and fabric softener into the

   dispenser, then close the drawer.

4.Choose a program you need .

5.Press “ Start/Pause” button to start the washing machine.

6.When the cycle is finished, there is a warning tone sound.

12

11

When the machine is started , the door lock is locked 

When the temperature inside the durm is above 60

℃

, the door lock is locked. 

When the water is above a certain level, the door lock is locked. 

When the washing cycle is finished, the door lock is unlocked.

How to use washer

Use process

Door lock

Important:

Do not try to open the door when the washing cycle is not finished or power supply is cut off

during the washing cycle, because the temperature may be high and you may be scalded.

Use process

Cleanness and Maintenance

Disconnect the machine from the mains electricity supply and withdraw the plug from

the socket before cleaning the machine.

The washing machine must not be hosed down.

Cleaning the exterior 

Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a well wrung-out

cloth. Wipe dry with a soft cloth.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.

These might damage plastic surfaces and other components because of the chemicals

they contain.

The washing drum

Clean the drum every 3 months by using the “Drum Clean” programme.

Cleaning the drawer

Remove detergent residues regularly.

Clear

the

drawer

following

these

:

Pull out the

drawer until a resistance is felt. 

Press

down the release catch and at the same time

pull the drawer right out of

the machine.

Remove the siphon from

compartment 

and

clean

it

.

Clean the 

dispenser

using a brush and warm water.

When washing cycle is finished, the machine will change into standby mode.

And the machine will be sleeping after 10 minutes without any control on the 

control panel.

Main wash compartment

Fabric softener compartment

Pre-wash compartment

The machine is fitted with a balance control device, which ensures the machine is stable

during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed

in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen

several times before the unbalance disappears and normal spinning can resume. If, after

about 20 minutes, the laundry is still not evenly distributed in the drum, the machine will not

spin. In this case, redistributed the load manually and reselect the spin program. 

».  

Do not exceed the maximum level mark.

3.  Close the drawer.

The right amount to dispenser will depend on the following:

•  The quantity of laundry

•  The soiling level of the laundry

- Lightly soiled 

No visible dirt or stains. Possibly slight 

body odour.

- Normally soiled 

Visibly dirty and/or just a few slight stains.

- Heavily soiled 

Visible dirt and stains and/or dried on 

soiling. The water hardness level.

WASHING STEPS

1.  Turn on the water tap, and connect the power.
2.  Open the door, and put the cloth into the drum one by one.
3.  Close the door, and put suitable amount of  detergent and fabric 

softener into the dispenser, then close the drawer.

4.  Choose a program you need .
5.  Press “ Start/Pause” button to start the washing machine.
6.  When the cycle is finished, there is a warning tone sound.

1. Open the drawer and add adequate detergent into main wash compartment marked “     

” or “  

 ”.

2. Add the fabric softener into compartment marked “       ” or “     ” .

    Do not exceed the maximum level mark.

3. Close the drawer.

How to use washer

Use process

Using the detergent drawer

The right amount to dispenser will depend on the following:

The quantity of laundry

The soiling level of the laundry

- 

Lightly soiled

   No visible dirt or stains. Possibly

slight body odour.

- 

Normally soiled

Visibly dirty and/or just a few slight

stains.

- 

Heavily soiled

Visible dirt and stains and/or dried on

soiling.

The water hardness level.

It is recommended to use low foaming powder for all washing temperature programs.

Washing steps

1.Turn on the water tap, and connect the power.

2.Open the door, and put the cloth into the drum one by one.

3.Close the door, and put suitable amount of  detergent and fabric softener into the

   dispenser, then close the drawer.

4.Choose a program you need .

5.Press “ Start/Pause” button to start the washing machine.

6.When the cycle is finished, there is a warning tone sound.

12

11

When the machine is started , the door lock is locked 

When the temperature inside the durm is above 60

℃

, the door lock is locked. 

When the water is above a certain level, the door lock is locked. 

When the washing cycle is finished, the door lock is unlocked.

How to use washer

Use process

Door lock

Important:

Do not try to open the door when the washing cycle is not finished or power supply is cut off

during the washing cycle, because the temperature may be high and you may be scalded.

Use process

Cleanness and Maintenance

Disconnect the machine from the mains electricity supply and withdraw the plug from

the socket before cleaning the machine.

The washing machine must not be hosed down.

Cleaning the exterior 

Clean the exterior with a mild non-abrasive cleaning agent or soap and water using a well wrung-out

cloth. Wipe dry with a soft cloth.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaning agents.

These might damage plastic surfaces and other components because of the chemicals

they contain.

The washing drum

Clean the drum every 3 months by using the “Drum Clean” programme.

Cleaning the drawer

Remove detergent residues regularly.

Clear

the

drawer

following

these

:

Pull out the

drawer until a resistance is felt. 

Press

down the release catch and at the same time

pull the drawer right out of

the machine.

Remove the siphon from

compartment 

and

clean

it

.

Clean the 

dispenser

using a brush and warm water.

When washing cycle is finished, the machine will change into standby mode.

And the machine will be sleeping after 10 minutes without any control on the 

control panel.

Main wash compartment

Fabric softener compartment

Pre-wash compartment

The machine is fitted with a balance control device, which ensures the machine is stable

during the spin. To protect the machine, it will cut in if the laundry is not evenly distributed

in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen

several times before the unbalance disappears and normal spinning can resume. If, after

about 20 minutes, the laundry is still not evenly distributed in the drum, the machine will not

spin. In this case, redistributed the load manually and reselect the spin program. 

53