DEWALT DCD996NT - Инструкция по эксплуатации - Страница 13

11

English

Variable Speed Switch (Fig. A)

To turn the tool on, squeeze the trigger switch 

 1 

. To turn the 

tool off, release the trigger switch. Your tool is equipped with 
a brake. The chuck will stop as soon as the trigger switch is 
fully released.

nOTE: 

Continuous use in variable speed range is not 

recommended. It may damage the switch and should 
be avoided.

Side Handle (Fig. A)

WARNING: 

To reduce the risk of personal injury, 

ALWAYS

operate the tool with the side handle properly installed. 
Failure to do so may result in the side handle slipping 
during tool operation and subsequent loss of control. Hold 
tool with both hands to maximize control.

The side handle 

 7 

 clamps to the front of the gear case and may 

be rotated 360˚ to permit right- or left-hand use. Side handle 
must be tightened sufficiently to resist the twisting action of 
the tool if the accessory binds or stalls. Be sure to grip the side 
handle at the far end to control the tool during a stall.
If model is not equipped with side handle, grip drill with one 
hand on the handle and one hand on the battery pack.

nOTE:

 Side handle comes equipped on all models.

Forward/Reverse Control Button (Fig. A)

A forward/reverse control button 

 2 

 determines the direction of 

the tool and also serves as a lock off button.
To select forward rotation, release the trigger switch and 
depress the for ward/re verse control button on the right side of 
the tool.
To select reverse, release the trigger switch and depress the 
forward/reverse control button on the left side of the tool.
The center position of the control button locks the tool in the off 
position. When changing the position of the control button, be 
sure the trigger is released.

nOTE:

 The first time the tool is run after changing the direction 

of rotation, you may hear a click on start up. This is normal and 
does not indicate a problem.

Torque Adjustment Collar/Electronic Clutch 
(Fig. C–E)

Your tool has an electronic adjustable torque screwdriver 
mechanism for driving and removing a wide array of fasteners. 
Circling the torque adjustment collar 

 5 

 are numbers. These 

numbers are used to set the clutch to deliver a torque range. 
The higher the number on the collar, the higher the torque and 
the larger the fastener which can be driven. To select any of the 
numbers, rotate until the desired number aligns with the arrow.

Three-Speed Gearing (Fig. A, C–E)

The three-speed feature of your tool allows you to shift gears 
for greater versatility. To select speed 1 (highest torque setting), 
turn the tool off and permit it to stop. Slide the gear shifter 

 6 

all the way forward. Speed 2 (middle torque and speed setting) 
is in the middle position. Speed 3 (highest speed setting) is to 
the rear.

nOTE: 

Do not change gears when the tool is running. Always 

allow the drill to come to a complete stop before changing 
gears. If you have trouble changing gears, make sure that the 
gear shifter is engaged in one of the three speed settings.
If the speed shifter becomes stuck or is difficult to select the 
desired gear, pull the trigger switch 

 1 

 to rotate the motor. Then 

select the gear.

Keyless Single Sleeve Chuck (Fig. F–H)

WARNING:

 Do not attempt to tighten drill bits (or 

any other accessory) by gripping the front part of the 
chuck and turning the tool on. Damage to the chuck 
and personal injury may result. Always lock off trigger 
switch and disconnect tool from power source when 
changing acces sories.

WARNING: 

Always ensure the bit is secure before starting 

the tool. A loose bit may eject from tool causing possible 
personal injury.

Your tool features a keyless chuck with one rotating sleeve for 
one-handed operation of the chuck. To insert a drill bit or other 
accessory, follow these steps.

1.  Turn off tool and disconnect tool from power source.
2.  Grasp the black sleeve of the chuck 

 4 

 with one hand and 

use the other hand to secure the tool as shown in Figure F. 
Rotate the sleeve counterclockwise (as viewed from the 
front) far enough to accept the desired accessory.

3.  Insert the accessory about 19 mm into the chuck (Fig. G). 

Tighten securely by rotating the chuck sleeve clockwise 
with one hand while holding the tool with the other hand 
(Fig. H). Continue to rotate the chuck sleeve until several 
ratchet clicks are heard to ensure full gripping power.

To release the accessory, repeat Steps 1 and 2 above.
Be sure to tighten chuck with one hand on the chuck sleeve and 
one hand holding the tool for maximum tightness.

LED Worklight (Fig. A)

The LED worklight 

 3 

 and its worklight switch 

 13 

 are located on 

the foot of the tool. The worklight is activated when the trigger 
switch is depressed. The low 

 14 

, medium 

 15 

 and spotlight 

 16 

modes can be changed by moving the switch on the foot of the 
tool. If the trigger switch remains depressed, the worklight will 
remain on in all modes.
When on low 

 14 

 and medium 

 15 

 settings, the beam will 

automatically turn off 20 seconds after the trigger switch 
is released.

Spotlight Mode

The high setting 

 16 

 is the spotlight mode. The spotlight will 

run for 20 minutes after the trigger switch is released. Two 
minutes before the spotlight will shut off, it will flash twice and 
then dim. To avoid the spotlight shutting off, lightly tap the 
trigger switch.

WARNING: 

While using the worklight in medium or 

spotlight mode, do not stare at the light or place the drill in 
a position which may cause anyone to stare into the light. 
Serious eye injury could result.