TESY CN 04 250 EIS W 304190 - Инструкция по эксплуатации - Страница 7

Operation and Storage Manual

7

EN

English

not need store every single hour until 19 h, and you only need 

to store the temperature to be 23°C at 19 h. By default the 

temperature will be 22°C during this period of time (7 – 19 h).

The procedure for storing each point is as follows:

Upon entering settings mode the display will show dAY1, 

with the numeral blinking to indicate that this is the 

parameter to be set (in this case it is the day of the week).

a. 

to select the desired day, use the   and   buttons 

b. 

to go to time setting, shortly press the “

Timer

” button

c. 

use the   and   buttons to select the desired time 

(with a 0.5h interval) per point 

d. 

to go to temperature setting, shortly press the “

Timer

” 

button 

e. 

to select the desired temperature, use the   and   

buttons. The possible temperature range is from 10 to 

30°С, and OFF status is possible as well.

f. 

To store the point, shortly press the “Timer” button; 

then you are automatically transferred to the setting of 

the next point (the display again shows dAYX) and you 

can proceed with paragraph а) for the next point.

g. 

When you have stored a point in the last hour of the 

day – 23.5h, you cannot store any more points for this 

day in the current setting, and the display will show 

“FUL_” and the number of the day.

ATTENTION:

 Points of a particular day may be 

stored only in ascending order of their times.

Note: 

Before implementing paragraph 

f)

 the user can go 

back to paragraph 

а)

 to correct the three parameters of 

a point by shortly pressing the 

ON/OFF

 button, without storing 

the settings in the memory.

Adding more points in a particular day may be done 

at random, after you have stored points for other days, 

however  you need to observe the rule for ascending 

order of their times in a day.
To exit the settings mode, press continuously the 

“Timer” button and wait for 30 seconds.
Upon leaving the settings you can review the stored 

points by using the   and   buttons, provided that 

the appliance is in programming mode.

Note: 

When you turn on the appliance, it will start 

operating in the (heating or programming) mode which 

it has last operated.

Note: 

You can switch between the modes of operation 

(heating or programming) by shortly pressing the 

“

Timer

” button when the appliance is switched on.

“Return to factory settings” function

When the convector is in “Off ” mode, press the   and 

 buttons simultaneously for six seconds; then the 

display will show „_ _ __“ and rotating symbols. When 

it is “reset”, the display will show the measured value of 

the room temperature.

After using the reset function, you need to re-enter the 

settings of the following functions:

 •

time setting

 •

enter a value of the temperature correction (if needed)

 •

disable the “Anti-frost” function (if needed)

 •

disable the “Adaptive start” (if needed)

 •

weekly programme - 24/7

If the electric convector is disconnected from the 

mains, this will not affect the set temperature and the 

mode of operation which has been active prior to its 

disconnection. If for example the convector has been 

in “Heating” mode, after it has been disconnected and 

reconnected to the mains, it will continue operating in 

the same mode with the same set temperature.

The principle of operation of the electric 

convector with energy-independent memory is to 

store the settings for 90 minutes guaranteed, and up to 

150 minutes not guaranteed.

When the room temperature is lower than the 

temperature set by the electronic thermoregulator, 

the convector will start operating and will continue 

operating until the room temperature reaches the set 

value. When the room temperature is higher than the 

temperature set by the electronic thermoregulator, the 

convector will automatically go into “Standby” mode.

Information presented on panel heater display

Indications when you are not in settings mode:

a. 

In Off mode – consecutively showing: 

 •

time (hour and minutes)

 •

measured room temperature 

b. 

In Heating mode – it shows the measured room 

temperature 

c. 

In Programming mode – consecutively showing:

 •

Day of the week, low line and the measured 

temperature. 6_22

 •

Day of the week, low line and the temperature set in 

the programme blinking (set for the current hour), 

which may be also the OFF symbol.  6_23

d. 

Upon connecting the convector to power supply the 

display shows:

 •

Hyphens “----“, if the appliance has been in Off mode 

before disconnecting it from the power supply. 

 •

Hyphens “----“, which in 2 seconds will be 

replaced by the value of the current temperature, 

if the appliance has been in On mode before 

disconnecting it from the power supply.

e. 

Two numerals (01÷96) and a blinking yellow LED 

indicate the remaining time in hours until the delayed 

start, if the appliance has been in “Delayed start” 

mode before disconnecting it from the power supply.

f. 

With the purpose of further energy saving, the 

electronic thermoregulator reduces the brightness