Efco IP 1550 38251 - Инструкция по эксплуатации - Страница 19

18

2  f

eatureS

anD

 t

eChnICal

 S

PeCIfICatIonS

PW 140 - IP 1400

PW 150C - IP 1500S

PW 155 - IP 1550

ELECTRICAL CONNECTION

Mains power supply

230 V   /   1~50 Hz

Absorbed power

2,0 kW

2,3 kW

Fuse

16 A

HYDRAULIC CONNECTION

Maximum inlet water temperature

50 °C   /   122 °F

Minimum inlet water temperature

5 °C   /   41 °F

Minimum inlet water low

500 l/h  /  132 US gph

600 l/h  /  159 US gph

Maximum inlet water pressure

0,8 MPa  /  8 bar  /  116 psi

Maximum priming depth

0 m   /   0 in

PERFORMANCE

Water low

410 l/h  /  108 US gph

480 l/h  /  127 US gph

Maximum pressure

14 MPa  /  140 bars 

2031 psi

14,5 MPa  /  145 bars 

2103 psi

15 MPa  /  150 bars 

2175 psi

Recoil of cleaner gun

14 N

16 N

15 N

Sound level

75 dB (A)

81 dB (A)

 77,2 dB (A)

Operator arm vibrations

1,14 m/s

2

2,24 m/s

2

1,77 m/s

2

WEIGHT AND DIMENSION

Lenght x width x height

38 x 32 x 89 cm   /   15 x 13 x 35 in

Weight

17 kg   /   37 lb

19 kg   /   42 lb

18 kg   /   40 lb

Detergent bottle capacity

0,3 l   /   0,08 US gal

All features and technical speciications are only indications. The Manufacturer reserves 

the right to modify the appliance as it deems necessary.

2.1 I

DentIfICatIon

of

 C

omPonentS

Please also refer to figures 1 to 2, which are located at the start of these operating and maintenance instructions.

1   Water inlet fast connector 

  2   Main switch
  3   Hose reel lever (only PW 150C - IP 1500S)
  4   Hose reel (only PW 150C - IP 1500S)
  5   High-pressure hose for the hose reel connection 

(only PW 150C - IP 1500S)

  6   Water outlet connector
  7   High-pressure hose for the hose reel 

(only PW 150C - IP 1500S)

  9   Seat for water gun/lance hose
 10   Plate “Read the manual before…”
 11   Wire reel

 12   Identiication plate

 13   Plate “Do not spray towards persons, ….”
 14   Power supply wire
 16   Water gun
 17   Lance hose

 18   Nozzle-holding head
 19   Nozzle cleaning hole
 20   Rotating nozzle lance hose (only 

PW 150C - PW 155 - IP 1500S - IP 1550)

 21   Foaming lance
 22   Cleaner suction adjusting device
 23   Detergent bottle
 24   High-pressure hose (only PW 140 - PW 155 - 

IP 1400 - IP 1550)

 25   High-pressure hose fast connector (only 

PW 140 - PW 155 - IP 1400 - IP 1550)

 26   Water inlet ilter

 27   Water inlet fast connector 
 28   Water gun lever
 29   Water gun lever safety stop
 30   Handle

2.2 S

afety

 D

evICeS

This water cleaner is provided with the following safety devices:
a)

 thermal protector

  It’s a device that stops the water cleaner operation in case of motor overheating.
  In this case, proceed as follows:

•  switch the main switch (2) to position “0” and remove the plug from the power outlet;
•  press the lever (28) on the cleaner gun to eliminate any remaining pressure;
•  wait 10 to 15 minutes until the water cleaner cools down;
•  check that the instructions in the 

“CheCkS anD ConneCtIon to the maInS eleCtrICIty SuPPly”

section have been followed, particularly regarding any extension cord used;

•  replace the electric plug in the power outlet and repeat the start-up procedure described in the

 “oPeratIon” 

section.