Einhell TC-PG 25/1/E5 (4152600) - Инструкция по эксплуатации - Страница 19

GB

- 19 -

5.  Before starting the equipment

5.1 Electrical safety:

• 

Electric supply cables and connected equip-

ment  must be in perfect condition.

• 

The generator is to be operated only with 

• 

 equipment whose voltage specifications con-

form   with the generator‘s output voltage.

• 

Never connect the generator to the power 

supply (socket-outlet).

• 

Keep the cable length to the consumer as 

short as possible.

5.2 Environmental protection

• 

Dispose of soiled maintenance material and 

• 

operating materials at the appropriate collec-

tion point.

• 

Recycle packaging material, metal and plas-

tics.

5.3 Connecting to earth

The housing is allowed to be connected to earth 

in order to discharge static electricity. To do this, 

connect one end of a cable to the earth connec-

tion on the generator (Fig. 4) and the other end to 

an external earth (for example an earthing rod).

6. Operation

Important! 

You must 

fi

 ll up with engine oil and 

fuel before you can start the engine.

• 

Check the fuel level and top it up if necessary

• 

Make sure that the generator has sufficient 

ventilation

• 

Make sure that the ignition cable is secured to 

the spark plug

• 

Inspect the immediate vicinity of the gene-

rator

• 

Disconnect any electrical equipment which 

may already be connected to the generator

6.1 Starting the engine

• 

Open the petrol cock (13) by turning it down

• 

Move the ON/OFF switch (10) to position 

„ON”   with the key.

• 

Move the choke lever (11) to position IØI.

• 

Start the engine with the reversing starter (12) 

by pulling the handle forcefully. If the engine 

does not start, pull the handle again.

• 

Push the choke lever (11) back again after 

the engine has started.

Important!

When starting with the reserve starter, the motor 

may recoil suddenly as it starts up, resulting in 

hand injuries. Wear protective gloves when star-

ting the equipment.

6.2 Connecting consumers to the generator

• 

Connect the equipment you want to use to 

the 230 V~sockets (3).

Important:

 These sockets may be loaded con-

tinuously (S1) with 2100W and temporarily (S2) 

for a maximum of 5 minutes with 2300 W or for a 

maximum of 2 minutes (with a cold motor) with 

2400W.

• 

The generator is suitable for 230 V~ AC appli-

ances only.

• 

Do not connect the generator to the 

household mains system as this may result 

in damage to the generator itself or to other 

electrical appliances in your home.

Note:

 Some electrical appliances (power jigsaws, 

drills, etc.) may have a higher level of power con-

sumption when used in di

ffi

  cult conditions.

Some electrical appliances (for example televisi-

ons, computers, etc.) must not be powered by a 

generator.

If in doubt, consult the manufacturer of your ap-

pliance.

6.3 Overload cut-out 2 x 230 V socket-outlets

Important! The generator is 

fi

 tted with an 

overload cut-out.

This shuts down the sockets (3). You can restart 

the sockets (3) by pressing the overload cut-out 

(5).

Important!

 If this happens, reduce the electric 

power you are taking from the generator or remo-

ve any defective connected appliances.

Important!

 Defective overload cut-outs must be 

replaced only by overload cut-outs of identical 

design and with the same performance data. If 

repairs are necessary, please contact your custo-

mer service center.

6.4 Switching o

ff

  the engine

• 

Before you switch off the generator, allow it 

to run briefly with no consumers so that it can 

„cool  down”

• 

Move the ON/OFF switch (10) to position 

„OFF” with the key.

• 

Close the petrol cock

Anl_TC_PG_25_1_E5_SPK9.indb   19

Anl_TC_PG_25_1_E5_SPK9.indb   19

10.02.2022   10:19:25

10.02.2022   10:19:25