Ryobi RLM1956MEB 5133001922 - Инструкция по эксплуатации - Страница 9

English

7

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

 WARNING

$OZD\V SURWHFW KDQGV E\ ZHDULQJ KHDY\ JORYHV DQGRU

wrapping the cutting edges of the blade with rags and 
other material when performing blade maintenance. 
Contact with the blade could result in serious personal 
injury.

REPLACING THE CUTTING BLADE

6HH¿JXUH

Be careful during adjustment of machine to prevent 

HQWUDSPHQW RI ¿QJHUV EHWZHHQ PRYLQJ EODGHV DQG ¿[HG

parts of machine.
For best results, the mower blade must be kept sharp. 
Replace a bent or damaged blade immediately.

 WARNING

Only use replacement blades approved by the 
manufacturer of your mower. Using a blade not approved 
by the manufacturer of your mower is hazardous and 
could result in serious injury, damage your mower, and 
void your warranty.

 WARNING

'UDLQWKHIXHO¿UVWEHIRUHWLOWLQJWKHPRZHUWRUHSODFHWKH

blade.

1.  Stop the engine and disconnect the spark plug wire. 

Allow blade to come to a complete stop.

Turn the mower on its side (carburetor facing up).

3.  Wedge a block of wood between the blade and mower 

deck to prevent the blade from turning.

Ɣ

Installing: See figure 7a.

Ɣ

Removing: See figure 7b.

4. 

8VLQJDLQZUHQFKRUVRFNHWQRWSURYLGHGORRVHQ

the blade bolt by turning the bolt in a counterclockwise 
direction as viewed from the bottom of the mower.

5. 

5HPRYH WKH EODGH EROW ORFN ZDVKHU ÀDW ZDVKHU DQG

blade.

6.  Place the new blade on the shaft. Make sure it is 

installed with the curved ends pointing up toward the 
mower deck and not down toward the ground.

7. 

5HSODFH WKH ÀDW ZDVKHU ORFN ZDVKHU DQG EODGH EROW

on the shaft. Finger tighten the bolt by turning in a 
clockwise direction as viewed from the bottom of the 
mower.

NOTE:

 Make certain all parts are replaced in the exact 

order in which they were removed.

8.  Torque the blade bolt down using a torque wrench (not 

provided) to ensure the bolt is properly tightened.

9.  The recommended torque for the blade bolt is 48–55 

Nm (35–40 ft.lb.).

NOTE: 

Do not sharpen the blades, replace with new 

item. Blades need to be properly balanced to avoid 

damage and personal injury.

CLEANING THE AIR FILTER

6HH¿JXUH

)RU SURSHU SHUIRUPDQFH DQG ORQJ OLIH NHHS WKH DLU ¿OWHU

clean.
1. 

5HPRYH WKH DLU ¿OWHU FRYHU E\ SXVKLQJ GRZQ WKH ODWFK

while gently pulling out the cover.

 5HPRYHWKHDLU¿OWHUDQGFOHDQLWLQZDUPVRDS\ZDWHU

Rinse and let dry completely.

3. 

$SSO\ D OLJKW FRDW RI HQJLQH RLO WR WKH DLU ¿OWHU WKHQ

squeeze it out using an absorbent cloth or paper towel.

4. 

5HLQVWDOOWKHDLU¿OWHULQWRWKHDLU¿OWHUEDVH

5. 

5HSODFHDQGVHFXUHWKHDLU¿OWHUFRYHU

NOTE:

 The filter should be replaced annually for best 

performance.

FUEL CAP

 WARNING

$OHDNLQJIXHOFDSLVD¿UHKD]DUGDQGPXVWEHUHSODFHG

immediately.

7KH IXHO FDS FRQWDLQV D QRQVHUYLFHDEOH ¿OWHU DQG D

check valve. A clogged fuel cap will cause poor engine 
performance. If performance improves when the fuel cap 
is loosened, check valve may be faulty or clogged. Replace 
fuel cap if required.

CHANGING THE ENGINE OIL

6HH¿JXUH

Ensure the fuel tank is completely empty before tipping the 
unit over otherwise fuel will leak out.

(QJLQHRLOVKRXOGEHFKDQJHGDIWHUHYHU\KRXUVRIXVH

Change the oil while the engine oil is still warm, but not hot. 
This allows the oil to drain quickly and completely.
1. 

5HPRYHWKHRLO¿OOFDSGLSVWLFN

Tip mower onto its side and allow oil to drain from the oil 

¿OOKROHLQWRDQDSSURYHGFRQWDLQHU

3. 

3ODFH PRZHU XSULJKW DQG UH¿OO ZLWK RLO IROORZLQJ WKH
LQVWUXFWLRQVLQWKH$GGLQJ&KHFNLQJ2LOVHFWLRQ

NOTE: 

Used oil should be disposed of at an approved 

disposal site. See your local oil retailer for more 
information.

MAINTAINING THE SPARK PLUG

6HH¿JXUH

The spark plug must be properly gapped and free of 
deposits in order to ensure proper engine operation. To 
check:
1.  Remove spark plug boot.

Clean any dirt from around base of spark plug.

3. 

5HPRYHVSDUNSOXJXVLQJDLQVSDUNSOXJVRFNHW

(not provided).

4.  Inspect spark plug for damage, and clean with a wire 

brush before reinstalling. If insulator is cracked or