Oursson PB1550HTD/RD - Инструкция по эксплуатации - Страница 7

12

13

ELEmENTS OF DESIGN, 

Fig. B

Measuring cup

Lid

Sealing ring

Blender’s cup

Blade unit 

Device’s body

Control panel

The knives are very sharp, be careful. 

UTILIZATION, Pic. c 

cONTROL PANEL, 

Pic. C-1

ON/OFF

 button is located on the bottom of the device’s 

body:

«О»

 - power off

«I»

 - power on

Use Rotary switch for the following functions:

• 

START/STOP 

the device

• Changing rotation’s speed and time

 - use this button to change 

the speed of rotation

 - use this button to 

set the timer, 0-9 min

. 

 - use this button to 

crush ice

 - use this button to 

make smoothies

 - use this button to 

make jam

 - use this button to 

heat up

 - use this button for 

Turbo mode

Display, 

Pic. C-2 

1. 

Rotation speed indication

2.  Temperature indication

3.  Time indication

Before first use, make one preparation cycle without 

ingredients, 

add water into the glass cup. After that, wipe 

the body of the device with a dry soft cloth. Wash the cup, 

lid, pusher, measuring cup and stainless steel knives with

warm water 

and detergent

. 

Before assembling and disassembling the device, 

make sure it is unplugged.

The  device  is  equipped  with  overload  and 

overheating protection. If there is an overload 

or an overheating, the device will automatically 

stop.  Unplug  the  device.  Let  it  cool  for  45 

minutes.  After  that,  you  can  continue  using 

the device.

Maximum time of continues use of the blender 

is 2 minutes, after that you need to turn off the 

device and let it cool for 3 minutes. Do not use 

the device without water or ingredients. 

When grinding hard products, do not use the 

device more than for 1 minute. Let the device 

cool for at least 5 minutes. 

Order of Operation:

1.  Plug in the device. Turn the 

ON/OFF

 switch into the 

«I»

position. All the buttons and the display will light up on 

the control panel, a sound signal will be heard, and then 

the device will go into standby mode. To exit standby 

mode, slightly press 

START/STOP

 button, all the 

buttons indication and the display will light up. 

2.  In standby mode, install the blender’s cup onto the 

motor unit according to the manual.

3.  Add required ingredients into the cup. Do not fill the 

cup above the 

mAX

 mark. Close the cup with lid.          

NOTE:

 The volume of the ingredients must not exceed 

2/3 of the volume of the cup.

4.  Select one of the preset modes ( 

 ), 

press 

START/STOP

 once.

5.  You can specify your own rotation speed and 

operational time parameters. In standby mode, press  

 button, with the help of rotary switch set the required 

rotation speed, press   button again. To set the 

operational time, repeat the steps using  .button. 

Press 

START/STOP

 once. The mixing/grinding process 

will start automatically. To stop the blender, press 

START/STOP

 again. 

NOTE: 

If the ingredients got stuck on the cup’s walls 

during mixing/grinding, use the pusher. Pusher can be 

used for stirring the ingredients during grinding/mixing.

Do not use the pusher for stirring more than 30 sec. 

6.  Remove the blender’s cup from the body of the device 

according to the manual. 

You can open the lid only 

when the cup is removed from the motor unit.

7.  Turn the switch at the bottom of the device to 

OFF

position  - 

«О»

. Unplug the device. After that, you can 

disassemble the device

.

PRESET mODES

PREPARATION REcOmmENDATIONS 

Before preparing, it is recommended to cut ingredients on 2x2x2 cm pieces. Max. amount of ingredients is shown in 

the table. Follow the recommendations in the recipe book.

Operation

Note

Smoothies and milk-

shakes

1500 ml

3 min.

Puree from fresh 

fruit, berries and 

vegetables 

1500 ml

MAX (8-10)

30-45 

sec.

The ingredients must be soft or juicy (bananas, strawber-

ries, cucumbers, etc.)

Puree from cooked 

fruits, vegetables and 

soups

750 ml

MAX(8-10)

30-45 

sec.

Do not puree ingredients with a temperature higher than 

80°С

Kneading dough for 

pancakes, omelets, 

etc.

1250 ml

MED (4-7)

30-45 

sec.

Suitable for every liquid dough

modes

Name

Description

Note

Smoothie

Preset: speed 10/3 minutes, indication  -   , set time 

and speed is shown on the display, indication    is lit. 

Other mode’s indications are turned off. Total time of 

the mode is 3 minutes.

Timer countdown. 

Ice Crushing

Preset: speed 10/10 sec., next speed 3/5 sec., next 

speed 10/3 sec – total 6 cycles,  indication -  , set 

time and speed is shown on the display, indication 

 is 

lit. Other mode’s indications are turned off. Total time of 

the mode is 1 min. 48 sec.

Timer countdown. 

Jam

Preset: speed 8/2 minutes, indication -   , set time 

and speed is shown on the display, indication    is lit. 

Other mode’s indications are turned off. Total time of 

the mode is 2 minutes.

Timer countdown. 

Heat up

Preset: speed 10, temperature 65°С, can be changed 

to 35°C, 50 °C, 65°C, 80°C, indication  -   , set time 

and speed is shown on the display, indication    , 

и   is lit. Other mode’s indications are turned off. Total 

time of the mode is 9 minutes.

Timer countdown. 

Turbo

Press and hold 

 button, blender operates at max 

speed 10. Release the button - blender will stop. 

Maximum operation time 9 minutes. Other mode’s 

indications are turned off.

Timer

Manually set the required preparation time: from 0-1 

min/5 sec. gap, from 2-9 min/30 sec. gap. In heat up 

mode you can set temperature 35°C, 50°C, 65°C, 

80°C.

Timer countdown. 

Rotation speed

Manually set the required rotation speed: from 1 to 10. 

Under load, the rotational speed at level 1 - 3000 ± 

10% rpm, at level 10 - 27000 ± 10% rpm.

PRODUcT SET

Measuring cup 

 ...................................................

 1 pc

Lid 

 ......................................................................

 1 pc

Sealing ring ........................................................

 1 pc

Blender’s cup 

 .....................................................

 1 pc

Pusher 

 ...............................................................

 1 pc

Blade unit 

...........................................................

 1 pc

Motor unit 

...........................................................

 1 pc

Instruction manual 

 .............................................

 1 pc

Warranty card  ....................................................

 1 pc