ELICA NAKED URBAN CAST IRON/F/25 - Инструкция по эксплуатации - Страница 18

18 

“Reset and configuration for filter saturation signal”)  

Note:

 The reset procedure may be activated by both the 

control panel and the remote control.  
 

Center light check 

The center light may be switched on and off by pressing the 

T2

 button on the control panel.  

Side light check (when scheduled) 

The side lights may be switched on and off by pressing AND 
HOLDING DOWN the 

T2 

button on the control panel.  

HOLDING DOWN the button, besides permitting to switch the 
hood on and off, it also regulates the light intensity given from 
the lights.   

Note:

 The switching on and off functions (and regulating 

function) alternate.   
The regulation of the light intensity is not available for hoods 
with neon lights.  
 

Reset and configuration for filter saturation signal  

Switch on hood to any speed (see above paragraph “Suction 
speed (power) selection”)   

 
Reset grease filter saturation signal (FLASHING GREEN 
LIGHT on control panel)   
First proceed with filter maintenance as described in 
corresponding paragraph.  

Press and hold down (for more than 3 seconds) the 

T1 

button 

on the control panel, the LED light will stop flashing indicating 
that the signal reset has been carried out, the hood will switch 
off.  
 

Reset coal filter saturation signal (FLASHING ORANGE 
(amber) LED light)  
First proceed with filter maintenance as described in 
corresponding paragraph. 

Press and hold down (for more than 3 seconds) the 

T1 

button 

on the control panel, the LED light will stop flashing indicating 
that the signal reset has been carried out, the hood will switch 
off. 
 

Coal filter saturation signal disactivaction (for particular 
applications)  

Switch off hood (see above paragraph “suction speed (power) 
selection”).  
Press and hold down (for more than 5 seconds) the 

T1 

button 

on the control panel, the LED light will start flashing GREEN 
indicating that the coal filter saturation signal has been 
disactivated.  
In order to reactivate the coal filter saturation signal, repeat 
operation, the LED light will flash ORANGE (amber)  

Command panel disassembly. 

Remove equipment from electrical grid.  
Remove grease filter.  
Disconnect connectors.  
Extract command panel by lifting it with a small screwdriver or 
similar tool.

Fig. 12 

Maintenance 

Cleaning 

Clean using 

ONLY

 the cloth dampened with neutral liquid 

detergent. 

DO NOT CLEAN WITH TOOLS OR 

INSTRUMENTS

. Do not use abrasive products. 

DO NOT USE 

ALCOHOL! 

Grease filter - 

Fig. 11 

Traps cooking grease particles. 

This must be cleaned once a month (or when the filter 
saturation indication system – if envisaged on the model in 
possession – indicates this necessity)  using non aggressive 
detergents, either by hand or in the dishwasher, which must 
be set to a low temperature and a short cycle. 
When washed in a dishwasher, the grease filter may discolor 
slightly, but this does not affect its filtering capacity. 

Charcoal filter (filter version only) - 

Fig. 11 

It absorbs unpleasant odors caused by cooking. 

The charcoal filter can be washed once every two months 
using hot water and a suitable detergent, or in a dishwasher at 
65°C (if the dishwasher is used, select the full cycle function 
and leave dishes out). 
Eliminate excess water without damaging the filter, then put it 
in the oven for 10 minutes at 100° C to dry completely. 
Replace the mattress every 3 years and when the cloth is 
damaged. 

Replacing lamps 

The hood is equipped with a lighting system based on LED 
technology. 
The LEDs guarantee an optimum lighting, a duration up to 10 
times as long as the traditional lamps and allow to save 90% 
electrical energy. 
 
To purchase spare LEDs, contact the technical assistance 
service. 

Removing the bulb:  

rotate anti-clockwise a quarter turn and take out.   

Mounting the bulb:  

insert the bulb in its seat so that its contacts enter the 
congruent  seats on the bulb-holder, rotate clockwise for about 
a quarter turn. 
If the lights do not work, make sure that the lamps are fitted 
properly into their housings before you call for technical 
assistance.