Timberk SWH RED3 80 V - Инструкция по эксплуатации - Страница 11

Водонагреватели Timberk SWH RED3 80 V - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 29
Загружаем инструкцию
background image

www.timberk.com • electrical storage water heater

10

9. MAINTENCE

Fig. 8

Fig. 9

1. Check the power plug and outlet as often as possible. Secure electrical 
contact and also proper grounding must be provided. The plug and outlet 
must not heat excessively.

2. If the water heater is not used for a long time, especially in regions with 
low air temperature (below 0°C), it is necessary to drain water from the 
heater to prevent damage of the water heater (due to water freezing in the 
internal tank).

3. To ensure long reliable water heater operation, it is recommended to 
regularly clean the internal tank and remove deposits on the electric heating 
element of the water heater, as well as check condition (fully decomposed 
or not) of the magnesium anode and, if necessary, replace it with a new one 
in case of full decomposition.

4. Tank cleaning frequency depends on hardness of water located in this 
territory. Cleaning must be performed by special maintenance services. 
You can ask the seller for address of the nearest service center or find it on 
the website www.timberk.com. 

Preventive operations must be performed upon strict observance of the 
operation manual and safety precautions.

5. The water heater is equipped with a thermal switch, which cuts off power 
supply of the heating element upon water overheating or its absence in the 
water heater. If the water heater is connected to the mains, but water is 
not heated and the indicator doesn’t light up, then the thermal switch was 
switched off or not switched on. To reset the water heater to the operating 
condition, it is necessary to:

- de-energize the water heater, remove the plate of the side / lower cover. 

- press the button, located at the center of the thermal switch, Fig.10;

- if the button is not pressed and there is no clicking, then you should wait 
until the thermal switch cools down to the initial temperature.

IMPORTANT! 

The manufacturer provides an extended guarantee 

for particular water heater components provided that 

timely and proper routine maintenance is performed 

by specialists of an authorized service center (see the 

guarantee slip).

Содержание

Полезные видео

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к Timberk SWH RED3 80 V?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"