Yamaha RX-V665 - Инструкция по эксплуатации - Страница 24

22

 En

BASIC OPERATION

1

Turn on external components (TV, DVD 
player, etc.) connected to this unit.

2

Press 

O

INPUT

l

 / 

h

 (or 

h

Input 

selection keys

) to select an input source.

The name of the selected input source is displayed for 
a few seconds.

y

•

You can change the input source name displayed on the front panel 
display or the OSD on the video monitor as necessary (see 
page 48).

3

Play the external component that you have 
selected as the source input, or select a radio 
station on the tuner.

Refer to the operating instructions of the external 
component for details on playback. For selecting 
radio stations or playback of an iPod or Bluetooth 
component using this unit, see the following.

•

FM/AM radio tuning (see page 29)

•

Bluetooth component playback (see page 35)

•

iPod playback (see page 33)

4

Turn the 

Q

VOLUME

control

 to adjust the 

volume (or press 

p

VOLUME +/–

).

This unit has a SCENE function that allows you to change 
input sources and sound field programs with one key. Four 
scenes are available for different usages, such as playing 
movies or music. The following input sources and sound 
field programs are provided as the initial factory settings.

y

•

When this unit is on standby, you can turn on this unit by pressing the 
SCENE key.

•

If a Yamaha DVD player that can receive SCENE control signals is 
connected to the REMOTE OUT jack of this unit, the DVD player 
automatically turns on and starts playback when 

J

SCENE

 (or 

l

SCENE

) is pressed. For details, refer to the instruction manual of the 

DVD player.

Press 

J

SCENE

 (or 

l

SCENE

).

Select the desired input source/sound field 
program, and press down 

J

SCENE

 (or 

l

SCENE

) until “SET Complete” appears on the 

front panel display.

When the OSD is shown on the video monitor, “SCENE 
Setting Complete” appears on the video monitor (OSD).

You can operate an external component with the remote 
control of this unit by setting a remote control code for the 
external component for each input source. Setting remote 
control codes for desired input sources allows you to 
switch between external components linked to scene 
selections.

1

Register the remote control code of an 
external component to the desired input 
source (see page 52).

Note

•

Remote control codes cannot be registered to TUNER input.

Playback

Basic procedure

Note

When you play back a DTS-CD, noise may be output in some 

conditions, which may cause a speaker malfunction. Make sure 

that the volume is set to low before starting playback. If noise is 

output, do the following.

1) When only noise is output
If a DTS bitstream signal is not properly input to this unit, 
only noise is output. Connect the playback component to this 
unit by digital connection and play back the DTS-CD. If the 
condition is not improved, the problem may results from the 
playback component. Consult the manufacturer of the 
playback component.

2) When noise is output during playback or skip operation
Before playing back the DTS-CD, display the option menu 
after selecting the input source and set “Decoder Mode” to 
“DTS” (see page 36).

VOL.

     A V 1  

Input source name

VOL.

SW
C

L

R

SL

SR

V o l u m e  - 1 8 . 5 d B

Volume

Using the SCENE function

Input source

Sound field program

BD/DVD

HDMI 1

Straight

TV

AV 1

Straight

CD

AV 3

Straight

RADIO

TUNER

7ch Enhancer

Selecting a SCENE

Registering input source/sound field 
program

Switching remotely controlled external 
components linked to scene selections