Yamaha RX-V665 - Инструкция по эксплуатации - Страница 22

20

 En

Optimizing the speaker setting for your listening room (YPAO)

5

To select a sound character for adjustment, 
press 

o

Cursor

n

 to select “EQ Type” and 

then press 

o

Cursor

l

 / 

h

.

If this unit does not work when you press 

o

Cursor

, 

press 

m

SETUP

 once and then operate this unit. 

This unit has a parametric equalizer that adjusts the 
output levels for each frequency range. The equalizer 
is adjusted to produce a cohesive sound field based on 
automatically measured speaker characteristics. 
In “EQ Type,” you can select the following 
parametric equalizer characteristics suitable for the 
desired sound characteristics.

Natural

This adjusts all speakers to achieve natural sound. 
Select this if sounds in the high frequency range seem 
too strong when “EQ Type” is set to “Flat.”

Flat

This adjusts each speaker to obtain the same 
characteristics. Select this if your speakers have 
similar qualities.

Front

This adjusts each speaker to obtain the same 
characteristics as the front left and right speakers. 
Select this if your front left and right speakers have 
significantly better qualities than the other speakers.

6

Press 

o

Cursor

n

 to select “Start” and then 

press 

o

ENTER

 to start the setup procedure.

A countdown starts and a measurement starts in 10 
seconds. A loud test tone is output during 
measurement.

Notes

•

During the automatic setup procedure, do not perform any 
operation on this unit.

•

Press 

o

Cursor

k

 to cancel the automatic setup procedure.

When measurement is successfully completed, 
“YPAO Complete” appears on the front panel display 
and the results appear on the monitor.

SP

Displays the number of speakers connected to this unit in 
the following order: 
Total of Front and Center/Total of Surround and Surround 
Back/Subwoofer

DIST

Displays the speaker distance from the listening position 
in the following order: 
Closest speaker distance/Farthest speaker distance

LVL

Displays the speaker output levels in the following order: 
Lowest speaker output level/Highest speaker output level

Notes

•

If “ERROR” appears on the video monitor during “Auto Setup,” 
measurement is canceled and the type of error is displayed. For details, 
see “When an error message is displayed during measurement” 
(page 21).

•

If problems occur during measurement, “WARNING (XX)” (xx indicates 
the number of warning) appears above “RESULT” (see page 21).

7

Press 

o

ENTER

 to confirm the settings.

The speaker characteristics are adjusted according to 
measurement results. 
To cancel the operation, press 

o

Cursor

l

 / 

h

 to 

select “Cancel” and press 

o

ENTER

. 

When the following screen appears, remove the 
optimizer microphone. “Auto Setup” is now 
complete.

y

•

If you do not want to apply the measurement results, select “Cancel.”

•

Perform “Auto Setup” again if you change the number or positions of 
speakers.

•

If you press 

o

ENTER

 before removing the optimizer microphone, 

“1 Auto Setup” of “Speaker Setup” in the setup menu (see page 44) is 
displayed.

Measurement takes about 3 minutes. To obtain precise 
results, stay where you will not disturb the 
measurement, such as to the side of or behind the 
speakers or outside the room.

1 AutoSetup

RESULT

[ENTER]:Finish

SP:3/4/0.1
DIST:2.50/3.00m
LVL:-3.5/+4.5dB

.

>Set

Cancel

[]/[]:Select

p

[

The optimizer microphone is sensitive to heat. Store it 
in a cool place and away from direct sunlight after 
measurement. Do not leave it in a place where it will be 
subjected to high temperatures such on an AV 
component.

1 AutoSetup

AUTOSETUPComplete

[SETUP]:Exit

DisconnectMicrophone

PRESS[ENTER]