Husqvarna 325R 9679084-02 - Инструкция по эксплуатации - Страница 12

• Do not use the product if you cannot receive aid if an

accident occurs. Always make sure others know you

will operate the product before you start to operate

the product.

• Do not turn with the product before you make sure

that no persons or animals are in the safety area.

• Remove all unwanted materials from the work area

before you start. If the cutting attachment hits an

object, the object can eject and cause injury or

damage. Unwanted material can wind around the

cutting attachment and cause damage.

• Do not use the product in bad weather (fog, rain,

strong winds, risk of lightning or other weather

conditions.). Dangerous conditions (such as slippery

surfaces) can occur because of bad weather.

• Make sure that you can move freely and work in a

stable position.

(Fig. 18)
• Make sure that you cannot fall when you use the

product. Do not tilt when you operate the product.

• Always hold the product with your two hands. Hold

the product on the right side of your body.

(Fig. 19)
• Operate the product with the cutting attachment

below your waist.

• If the choke control is in the choke position when the

engine starts, the cutting attachment starts to turn.

• Do not touch the bevel gear after the engine stops.

The bevel gear is hot after the engine stops. Hot

areas can cause injury.

• Stop the engine before you move the product.
• Do not put down the product with the engine on.
• Before you remove the unwanted materials from the

product, stop the engine and wait until the cutting

attachment stops. Let the cutting attachment stop

before you or an aid remove the cut material.

Personal protective equipment

WARNING: Read the warning instructions

that follow before you use the product.

• Always use correct personal protective equipment

when you operate the product. The personal

protective equipment does not erase the risk of

injury. The personal protective equipment decreases

the grade of injury if an accident occurs.

• Always use an approved eye protection while you

operate the product.

• Do not operate the product with bare feet or with

open shoes. Always use heavy-duty slip-resistant

boots.

• Use heavy, long pants.
• If it is necessary, use approved protective gloves.
• Use a helmet if it is possible that objects fall on your

head.

• Always use approved ear protection while you

operate the product. Noise for a long period can

cause noise-induced hearing loss.

• Make sure that you have a first aid kit near.

Safety devices on the product

WARNING: Read the warning instructions

that follow before you use the product.

• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. Refer to 

Product overview on page 9.

• If the safety devices are defective, speak to your

Husqvarna servicing dealer.

Throttle trigger lockout
The throttle trigger lockout locks the throttle trigger.

(Fig. 20)

Push the throttle trigger lockout (A) to release the

throttle trigger (B). When you release the handle, the

throttle trigger lockout and the throttle trigger go back to

their initial positions.
1. Make sure that the throttle trigger (B) is locked at idle

when you release the throttle trigger lockout (A).

2. Push the throttle trigger lockout (A) and make sure

that it goes back to its initial position when you

release it.

3. Push the throttle trigger (B) and make sure that it

goes back to its initial position when you release it.

Start the engine, and then apply full throttle. Release the

throttle trigger and examine if the cutting attachment

stops. If the cutting attachment turns with the throttle in

the idle position, examine the idle adjustment screw of

the carburetor.

Stop switch
Start the engine. Make sure that the engine stops when

you move the stop switch to the stop position.
(Fig. 21)

Cutting attachment guard
The cutting attachment guard prevents a loose object to

eject in the direction of the operator.

(Fig. 22)

Examine the cutting attachment guard for damage and

replace if it is damaged. Only use the approved guard

for the cutting attachment.

Muffler
• Do not use an engine with a damaged muffler. A

damaged muffler increases the noise level and the

risk of fire. Keep a fire extinguisher near.

• Examine regularly that the muffler is attached to the

product.

12

881 - 001 - 10.10.2018