Dewalt 18 В XR FLEXVOLT ADVANTAGE XRP DCD999NT-XJ - Инструкция по эксплуатации - Страница 8

6

English

Mains Plug Replacement 
(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

•  Safely dispose of the old plug.
•  Connect the brown lead to the live terminal in the plug.
•  Connect the blue lead to the neutral terminal.

WARNING: 

No connection is to be made to the 

earth terminal.

Follow the fitting instructions supplied with good quality plugs. 
Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless absolutely 
necessary. Use an approved extension cable suitable for 
the power input of your charger (see 

Technical Data

). The 

minimum conductor size is 1 mm

2

; the maximum length 

is 30 m.
When using a cable reel, always unwind the cable completely.

Important Safety Instructions for All 
Battery Chargers

SAVE THESE INSTRUCTIONS:

 This manual contains important 

safety and operating instructions for compatible battery 
chargers (refer to 

Technical Data

).

•  Before using charger, read all instructions and cautionary 

markings on charger, battery pack, and product using 
battery pack.

WARNING: 

Shock hazard. Do not allow any liquid to get 

inside charger. Electric shock may result.

WARNING:

 We recommend the use of a residual current 

device with a residual current rating of 30mA or less.

CAUTION:

 Burn hazard. To reduce the risk of injury, 

charge only  

D

e

WALT

 rechargeable batteries. Other 

types of batteries may burst causing personal injury 
and damage.

CAUTION:

 Children should be supervised to ensure that 

they do not play with the appliance.

NOTICE: 

Under certain conditions, with the charger 

plugged into the power supply, the exposed charging 
contacts inside the charger can be shorted by foreign 
material. Foreign materials of a conductive nature such 
as, but not limited to, steel wool, aluminum foil or any 
buildup of metallic particles should be kept away from 
charger cavities. Always unplug the charger from the 
power supply when there is no battery pack in the cavity. 
Unplug charger before attempting to clean.

• 

DO NOT attempt to charge the battery pack with any 
chargers other than the ones in this manual. 

The charger 

and battery pack are specifically designed to work together.

• 

These chargers are not intended for any uses other than 
charging 

D

e

WALT

 rechargeable batteries. 

Any other uses 

may result in risk of fire, electric shock or electrocution.

• 

Do not expose charger to rain or snow.

Chargers

D

e

WALT

 chargers require no adjustment and are designed to be 

as easy as possible to operate.

Electrical Safety

The electric motor has been designed for one voltage only. 
Always check that the battery pack voltage corresponds to the 
voltage on the rating plate. Also make sure that the voltage of 
your charger corresponds to that of your mains.

i

Your 

D

e

WALT

 charger is double insulated in 

accordance with EN60335; therefore no earth wire 
is required.

If the supply cord is damaged, it must be replaced only by 

D

e

WALT

 or an authorised service organisation.

Residual Risks

In spite of the application of the relevant safety regulations 
and the implementation of safety devices, certain residual risks 
cannot be avoided. These are:

•  Impairment of hearing.
•  Risk of personal injury due to flying particles.
•  Risk of burns due to accessories becoming hot 

during operation.

•  Risk of personal injury due to prolonged use.

SAVE THESE INSTRUCTIONS

Safety Instructions When Using Long 
Drill Bits

• 

Never operate at higher speed than the maximum 
speed rating of the drill bit. 

At higher speeds, the bit is likely 

to bend if allowed to rotate freely without contacting the 
workpiece, resulting in personal injury.

• 

Always start drilling at low speed and with the bit tip 
in contact with the workpiece.

 At higher speeds, the bit is 

likely to bend if allowed to rotate freely without contacting the 
workpiece, resulting in personal injury.

• 

Apply pressure only in direct line with the bit and do not 
apply excessive pressure.

 Bits can bend causing breakage or 

loss of control, resulting in personal injury.

• 

Use clamps or other practical way to secure and support 
the workpiece to a stable platform. 

Holding the work by 

hand or against your body is unstable and may lead to loss 
of control.

• 

Wear ear protectors when hammering for extended 
periods of time. 

Prolonged exposure to high intensity noise 

can cause hearing loss. Temporary hearing loss or serious ear 
drum damage may result from high sound levels generated 
by hammerdrilling.

• 

Wear safety goggles or other eye protection. 

Hammering 

and drilling operations cause chips to fly. Flying particles can 
cause permanent eye damage.

• 

Hammer bits and tools get hot during operation. 

Wear 

gloves when touching them.