Bosch GEX 125 150 AVE - Инструкция по эксплуатации - Страница 18

18

 | English 

2 609 932 777 | (23.2.11)

Bosch Power Tools

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. 

The 

correct power tool will do the job better 
and safer at the rate for which it was de-
signed.

b) Do not use the power tool if the switch 

does not turn it on and off. 

Any power 

tool that cannot be controlled with the 
switch is dangerous and must be re-
paired.

c) Disconnect the plug from the power 

source and/or the battery pack from the 
power tool before making any adjust-
ments, changing accessories, or storing 
power tools. 

Such preventive safety 

measures reduce the risk of starting the 
power tool accidentally.

d) Store idle power tools out of the reach of 

children and do not allow persons unfa-
miliar with the power tool or these in-
structions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts, 
breakage of parts and any other condi-
tion that may affect the power tool’s op-
eration. If damaged, have the power tool 
repaired before use. 

Many accidents are 

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. 

Prop-

erly maintained cutting tools with sharp 
cutting edges are less likely to bind and 
are easier to control.

g) Use the power tool, accessories and tool 

bits etc. in accordance with these in-
structions, taking into account the work-
ing conditions and the work to be per-
formed. 

Use of the power tool for 

operations different from those intended 
could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qual-

ified repair person using only identical 
replacement parts. 

This will ensure that 

the safety of the power tool is maintained.

Safety Warnings for Sander

f

Use the machine only for dry sanding. 

Pen-

etration of water into the machine increases 
the risk of an electric shock.

f

Pay attention that no persons are put at risk 
through sparking. Remove any combustible 
materials in the vicinity. 

Sparking occurs 

when sanding metal materials.

f

Caution, fire hazard! Avoid overheating the 
object being sanded as well as the sander. 
Always empty the dust collector before tak-
ing breaks. 

In unfavourable conditions, e. g., 

when sparks emit from sanding metals, sand-
ing debris in the dust bag, micro filter or pa-
per sack (or in the filter sack or filter of the 
vacuum cleaner) can self-ignite. Particularly 
when mixed with remainders of varnish, poly-
urethane or other chemical materials and 
when the sanding debris is hot after long pe-
riods of working.

f

When working with the machine, always 
hold it firmly with both hands and provide 
for a secure stance. 

The power tool is guided 

more secure with both hands.

f

Secure the workpiece. 

A workpiece clamped 

with clamping devices or in a vice is held 
more secure than by hand.

f

Products sold in GB only

: Your product is fit-

ted with a BS 1363/A approved electric plug 
with internal fuse (ASTA approved to 
BS 1362).
If the plug is not suitable for your socket out-
lets, it should be cut off and an appropriate 
plug fitted in its place by an authorised cus-
tomer service agent. The replacement plug 
should have the same fuse rating as the orig-
inal plug.
The severed plug must be disposed of to 
avoid a possible shock hazard and should 
never be inserted into a mains socket else-
where.

Products sold in AUS and NZ only

: Use a 

residual current device (RCD) with a rated 
residual current of 30 mA or less.

OBJ_BUCH-1330-001.book  Page 18  Wednesday, February 23, 2011  9:55 AM