Ryobi R18MT-0 - Инструкция по эксплуатации - Страница 5

SHUVRQDOLQMXU\

Ŷ

When making a plunge cut into soft materials like wood 
and plasterboard using the cutting accessory, gradually 
bring the vibrating blade to the workpiece. Do not push 
the vibrating blade hard into the material to be cut. Let 
the product do the work and concentrate on keeping the 
product and the cutting accessory stable in the position 
you wish to make the cut.

Ŷ

8VH WKH GHSWK KHLJKW JDXJH WR KHOS VHW \RXU GHSWK RI

cut or prevent cutting too deeply into the material.

Ŷ

Take extra care when cutting in non-ferrous metals. 
The vibrating cutting blade may skip around before 
beginning the cut. If necessary, drill some holes along 
the line to be cut before you start cutting.

Ŷ

,I WKH FXWWLQJ DFFHVVRULHV EHFRPH MDPPHG LQ WKH

workpiece, switch off the product and disconnect from 
the power supply. If the cutting accessory cannot 
be removed easily, allow the cutting accessory to 
adequately cool before releasing the cutting accessory 
from the product. Wear gloves and use hand tools, such 
as pliers or wrench, to remove the cutting accessory 
from the workpiece.

OVERCURRENT PROTECTION

When overcurrent is detected, the product will automatically 
switch off.

If the product stops working, release the trigger and then 
apply again. The product should again start working.

MAINTENANCE

 WARNING

The product should never be connected to a power 

VXSSO\ ZKHQ DVVHPEOLQJ SDUWV PDNLQJ DGMXVWPHQWV

cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product from the power 
supply will prevent accidental starting that could cause 

VHULRXVLQMXU\

 WARNING

When servicing, use only original manufacturer’s 
replacement parts, accessories and attachments. Use of 
any other parts may create a hazard or cause product 
damage.

Ŷ

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to various types of commercial 
solvents and may be damaged by their use. Use clean 
cloths to remove dirt, carbon dust, etc.

 WARNING

'RQRWDWDQ\WLPHOHWEUDNHÀXLGVJDVROLQHSHWUROHXP

based products, penetrating oils, etc., come in contact 
with plastic parts. Chemicals can damage, weaken or 
destroy plastic which may result in serious personal 

LQMXU\

 WARNING

For greater safety and reliability, all repairs should be 
performed by an authorised service centre.

The dust from plaster and wall board is abrasive and may 
cause premature failure of the product if it is allowed to 
enter the motor area. Thoroughly clean the product after 
use by using a brush and a vacuum. Take care not to 
push dirt into the ventilation openings. Beware of using 
compressed air to clean the product because dust and grit 

FDQFDXVHVHULRXVH\HLQMXU\

LUBRICATION

All of the bearings in the product are lubricated with a 

VXI¿FLHQWDPRXQWRIKLJKJUDGHOXEULFDQWIRUWKHOLIHVSDQRI

the product under normal operating conditions. Therefore, 
no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories and 
packaging should be sorted for environment-
friendly recycling.

SYMBOLS ON THE PRODUCT

Safety alert

CE conformity

No-load speed

V

Volts

Direct current

EurAsian Conformity Mark

Please read the instructions carefully before 
starting the machine.

Ukrainian mark of conformity

3

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL