Whirlpool AXMT 6332/IX/1 - Инструкция по эксплуатации - Страница 36

GB

Switching the appliance off

Disconnect your appliance from the electricity supply
before carrying out any work on it.

Cleaning the oven

 Never use steam cleaners or pressure cleaners on

the appliance.

• Clean the glass part of the oven door using a

sponge and a non-abrasive cleaning product,
then dry thoroughly with a soft cloth. Do not use
rough abrasive material or sharp metal scrapers
as these could scratch the surface and cause the
glass to crack.

• The stainless steel or enamel-coated external

parts and the rubber seals may be cleaned using
a sponge which has been soaked in lukewarm
water and neutral soap. Use specialised products
for the removal of stubborn stains. After cleaning,
rinse and dry thoroughly. Do not use abrasive
powders or corrosive substances.

• The inside of the oven should ideally be cleaned

after each use, while it is still lukewarm. Use hot
water and detergent, then rinse well and dry with
a soft cloth. Do not use abrasive products.

• The accessories can be washed like everyday

crockery, and are even dishwasher safe.

• Dirt and grease should be removed from the control

panel using a non-abrasive sponge or a soft cloth.

•

Stainless steel can be marked by hard water that

has been left on the surface for a long time, or by
aggressive detergents that contain phosphorus.
We recommend that the steel surfaces are rinsed
well then dried thoroughly.

Inspecting the oven seals

Check the door seals around the oven regularly. If the
seals are damaged, please contact your nearest After-
sales Service Centre. We recommend that the oven is
not used until the seals have been replaced.

Care and maintenance

*

Only available in certain models.

Replacing the oven light bulb

1. After disconnecting the oven 
from the electricity mains, remove 
the glass lid covering the lamp 
socket (

see fi gure

).

2. Remove the light bulb and 
replace it with a similar one: 
voltage 230 V, wattage 25 W, 
cap E 14.

3. Replace the lid and reconnect the oven to the electricity 
supply.

 Do not use the oven lamp as/for ambient lighting.

Gas tap maintenance

Over time, the valves may become jammed or
difficult to turn. If this occurs, the valve must be
replaced.

This procedure must be performed by a

This procedure must be performed by a

This procedure must be performed by a

This procedure must be performed by a

This procedure must be performed by a

qualified technician who has been authorised by

qualified technician who has been authorised by

qualified technician who has been authorised by

qualified technician who has been authorised by

qualified technician who has been authorised by
the manufacturer.

the manufacturer.

the manufacturer.

the manufacturer.

the manufacturer.

36

Automatic cleaning using the SmartClean 
cycle

The SmartClean mode is an automatic cleaning cycle 
which releases steam inside the cavity and uses the exclusi-
ve SmartClean enamel to make it easy to remove any dirt 
residues from the cavity and accessories. Available in three 
different levels: Economy, Normal and Intensive - to be used 
based on the type of dirt.  
The SmartClean cycle can be used to keep the oven al-
ways clean. During the cleaning process steam is released 
inside the cavity which, together with the titanium-based
SmartClean enamel (on the inside walls of the oven and drip-
ping pans), makes it easy to clean the oven. 

In order to start the SmartClean cycle:

1. Wait for the oven to cool down.
2. Place the dripping pan on level 1 and pour in the following 
quantities of water: 150g for the Economy cycle, 250g for the 
Normal cycle and 350g for the Intensive cycle. A smaller or 
larger quantity of water than recommended may affect the 
cycle results. Do not use detergents.

3. Close the oven door.
4. Turn the programmer knob to TRADITIONAL function, and 
the thermostat knob to the temperature of 100’C
 To prevent any steam leaks do not open the door during the 
cycle.
 In the last minutes of the intensive cycle the control panel 
will partially and momentarily mist up. The mist will disappear 
every time the tangential cooling fan is started.

- 150 
- 250 
- 350 

-10
-15
-20

g

min

g
g

min
min