Einhell TC-TS 254 - Инструкция по эксплуатации - Страница 31

GB

- 31 -

• 

 Guide at the side with your left or right hand  

(depending on the position of the parallel 

stop) only as far as the front edge of the gu-

ard hood.

• 

 Always push the workpiece through to the 

end of the splitter (5).

• 

 The offcut piece remains on the saw table 

(1) until the blade (4) is back in its position of 

rest.

• 

 Secure long workpieces against falling off 

at the end of the cut (e.g. with a roller stand 

etc.).

8.1.1 Cutting narrow workpieces (Fig. 22)

Be sure to use a push stick (3) when making 

longitudinal cuts in workpieces smaller than 150 

mm in width. A push block is supplied with the 

saw! Replace a worn or damaged push stick im-

mediately.

8.1.2 Cutting extremely narrow workpieces 

(Fig. 23)

• 

 Be sure to use a push block when making  

longitudinal cuts in very narrow workpieces 

with a width of 50 mm and less.

• 

 The low guide face of the parallel stop is best  

used in this case. 

• 

There is no push block supplied with the 

saw! (Available from your specialist dealer). 

Replace the push block without delay when it 

becomes worn.

8.2 Making bevel cuts (Fig. 24)

Bevel cuts must always be used using the parallel 

stop (7).

If you tilt the saw blade (4) to the left when making 

angular cuts, position the parallel stop (7) on the 

right-hand side of the saw blade (4). Guide the 

workpiece between the saw blade (4) and the 

parallel stop (7).

• 

 Set the blade (4) to the desired angle. (See 

7.5.)

• 

 Set the parallel stop (7) in accordance with 

the workpiece width and height (see 7.3)

• 

 Carry out the cut in accordance with the work-

piece width (see 8.1.1., 8.1.2.)

8.3 Making cross cuts (Fig. 25)

• 

 Slide the cross stop (21) into one of the 

grooves (21) in the table and adjust to the 

required angle. (See 7.4.) If you also want to 

tilt the blade (4), use the groove (21) which 

prevents your hand and the cross stop from 

making contact with the blade guard.

• 

 Press the workpiece firmly against the cross 

stop (14).

• 

 Switch on the saw.

• 

 Push the cross stop (14) and the workpiece  

toward the blade in order to make the cut.

• 

Warning! 

Always hold the guided part of the workpiece. 

Never hold the part which is to be cut off.

• 

 Push the cross stop (14) forward until the  

workpiece is cut all the way through.

• 

 Switch off the saw again. Do not remove the  

offcut until the blade has stopped rotating.

9.  Replacing the power cable

Danger!

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

10. Cleaning, maintenance and 

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

10.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

10.2 Carbon brushes

In case of excessive sparking, have the carbon  

brushes checked only by a quali

fi

 ed electrician.

Danger!

 The carbon brushes should not be rep 

laced by anyone but a quali

fi

 ed electrician.

Anl_TC_TS_254_ECO_SPK9.indb   31

Anl_TC_TS_254_ECO_SPK9.indb   31

25.10.2019   10:22:50

25.10.2019   10:22:50