Einhell TC-TS 254 - Инструкция по эксплуатации - Страница 27

GB

- 27 -

Operating mode S6 40%: Continuous operation 

with idling (cycle time 10 minutes). To ensure that 

the motor does not become excessively hot, it 

may only be operated for 40% of the cycle at the 

speci

fi

 ed rating and must then be allowed to idle 

for 60% of the cycle.

Danger!

Noise

The noise emission values were measured in ac-

cordance with EN 62841.

Operation

L

pA

 sound pressure level  ..................... 93.2 dB(A)

K

pA

 uncertainty  ........................................ 3 dB(A)

L

WA

 sound power level   ..................... 106.2 dB(A)

K

WA

 uncertainty ........................................ 3 dB(A)

Wear ear-mu

ff

 s.

The impact of noise can cause damage to hea-

ring.

The stated noise emission values were measured 

in accordance with a set of standardized criteria 

and can be used to compare one power tool with 

another.

The stated noise emission values can also be 

used to make an initial assessment of exposure.

Warning:

The noise emission levels may vary from the level 

speci

fi

 ed during actual use, depending on the 

way in which the power tool is used, especially 

the type of workpiece it is used for.

Keep the noise emissions and vibrations to a 

minimum.

• 

 Only use appliances which are in perfect wor-

king order.

• 

 Service and clean the appliance regularly.

• 

 Adapt your working style to suit the appliance.

• 

 Do not overload the appliance.

• 

 Have the appliance serviced whenever ne-

cessary.

• 

 Switch the appliance off when it is not in use.

Limit the operating time!

All stages of the operating cycle must be conside-

red (for example, times in which the electric tools 

are switched o

ff

  and times in which the tool is 

switched on but operates without load).

Caution!

Residual risks

Even if you use this electric power tool in 

accordance with instructions, certain resi-

dual risks cannot be rules out. The following 

hazards may arise in connection with the 

equipment’s construction and layout:

1.   Lung damage if no suitable protective dust 

mask is used.

2.   Damage to hearing if no suitable ear protec-

tion is used.

5.  Before starting the equipment

Before you connect the equipment to the mains 

supply make sure that the data on the rating plate 

are identical to the mains data.

Warning! 

Always pull the power plug before making 

adjustments to the equipment.

• 

Unpack the bench-type circular saw and 

check it for damage which may have occurred 

in transit.

• 

 The machine has to be set up where it can 

stand firmly, e.g. on a work bench, or it must 

be bolted to a strong base.

• 

 All covers and safety devices have to be pro-

perly fitted before the machine is switched on.

• 

 It must be possible for the saw blade to run 

freely.

• 

 When working with wood that has been pro-

cessed before, watch out for foreign bodies 

such as nails or screws etc.

• 

 Before you actuate the On/Off switch, make 

sure that the saw blade is correctly fitted and 

that the machine’s moving parts run smoothly.

6.  Assembly

Danger! Pull out the power plug before carry-

ing out any maintenance, resetting or assem-

bly work on the circular saw!

6.1 Assembling the base frame (Fig. 3-6)

Danger! 

Make allowance for the weight of the 

machine and arrange another person to help you 

if necessary!

• 

Turn the bench-type circular over and set the 

saw down on the floor or on some other work 

surface. Important! Place suitable material 

(e.g. packaging material) between the table 

Anl_TC_TS_254_ECO_SPK9.indb   27

Anl_TC_TS_254_ECO_SPK9.indb   27

25.10.2019   10:22:49

25.10.2019   10:22:49