Ryobi RSDS18X-1C40S (5133005383) - Инструкция по эксплуатации - Страница 3

ENGLISH

EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL

3

Original Instructions

Safety, performance, and dependability have been given top 
priority in the design of your rotary hammer drill.

INTENDED USE

The rotary hammer drill is intended to be used only by 
adults who have read and understood the instructions and 
warnings in this manual, and can be considered responsible 
for their actions.
The rotary hammer drill is designed to operate without 
hammer function into wood and metal. For chiselling and 
masonry drilling, the hammer mode may be used.
The rotary hammer drill is designed to operate with drill bits up 
to the maximum diameter de

fi

 ned in the product speci

fi

 cations.

The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the 
product for operations different from intended could result in 
a hazardous situation.

WARNING!

Read all safety warnings, instructions, 

illustrations and specifications provided with this 
power tool.

 Failure to follow all instructions listed below 

may result in electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

ROTARY HAMMER DRILL SAFETY WARNINGS

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

■

Wear ear protectors.

 Exposure to noise can cause 

hearing loss.

■

Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

■

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory or fasteners may contact hidden wiring.

Cutting accessory or fasteners contacting a “live” wire 
may make exposed metal parts of the power tool “live” 
and could give the operator an electric shock.

SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS 
WITH ROTARY HAMMERS

■

Always start drilling at low speed and with the bit 
tip in contact with the workpiece.

 At higher speeds, 

the bit is likely to bend if allowed to rotate freely without 
contacting the workpiece, resulting in personal injury.

■

Apply pressure only in direct line with the bit and do 
not apply excessive pressure.

 Bits can bend causing 

breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY WARNINGS

■

Clamp workpiece with a clamping device. Unclamped 
workpieces can cause severe injury and damage.

■

When working in walls, ceiling, or floor, take care to 
avoid electric cables and gas or waterpipes.

■

Injuries may be caused, or aggravated, by prolonged 
use of a tool. When using any tool for prolonged periods, 
ensure you take regular breaks.

■

Dust created by operating the product can cause 
respiratory injury. Wear appropriate dust control mask 
with filters suitable for protecting against particles from 
the material being worked on.

■

The product will restart automatically if stalled. Switch 
off the product immediately if it stalls. Do not switch 

on the product again while it is still stalled, as doing so 
could trigger a sudden recoil with a high reactive force. 
Determine why the product stalled and rectify this, 
paying heed to the safety instructions.

■

Ambient temperature range for tool during operation is 
between 0 

˚

C and 40

˚

 C.

■

Ambient temperature range for tool storage is between 
0 

˚

C and 40

˚

 C.

■

The recommended ambient temperature range for the 
charging system during charging is between 10 

˚

C and 

38

˚

 C.

ADDITIONAL BATTERY SAFETY WARNINGS

■

To reduce the risk of fire, personal injury, and product 
damage due to a short circuit, never immerse your 
tool, battery pack or charger in fluid or allow a fluid to 
flow inside them. Corrosive or conductive fluids, such 
as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

■

Ambient temperature range for battery during use is 
between 0°C and 40°C.

■

Ambient temperature range for battery storage is 
between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps or 
tape. Do not transport batteries that are cracked or leaking. 
Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 56.

1.  Direction of rotation selector
2. SDS+ Chuck
3. Switch trigger
4. Mode selector
5.  Handle, insulated gripping surface
6. LED light
7. Battery port
8.  Depth guide rod
9. Operator's manual
10. Auxiliary handle, insulated gripping surface
11. Battery pack
12. Charger

MAINTENANCE

■

The product should never be connected to a power 
supply when assembling parts, making adjustments, 
cleaning, performing maintenance, or when the product 
is not in use. Disconnecting the product from the power 
supply will prevent accidental starting that could cause 
serious injury.

■

When servicing, use only original manufacturer’s 
replacement parts, accessories and attachments. Use 
of any other parts may create a hazard or cause product 
damage.