Makita DHR282ZJ - Инструкция по эксплуатации - Страница 18

18 ENGLISH

For DHR280/DHR282

Optional accessory

Attach the chuck adapter to a keyless drill chuck to 

which 1/2"-20 size screw can be installed, and then 

install them to the tool. When installing it, refer to the 

section “Installing or removing drill bit”.

► 

Fig.33:

1.

 Keyless drill chuck 

2.

 Chuck adapter

For DHR281/DHR283

Use the quick change drill chuck as standard equip-

ment. When installing it, refer to "changing the quick 

change chuck for SDS-plus".

Hold the ring and turn the sleeve counterclockwise to 

open the chuck jaws. Place the bit in the chuck as far as 

it will go. Hold the ring firmly and turn the sleeve clock

-

wise to tighten the chuck.

► 

Fig.34:

1.

 Sleeve 

2.

 Ring

To remove the bit, hold the ring and turn the sleeve 

counterclockwise.

Diamond core drilling

NOTICE:

If performing diamond core drilling 

operations using “rotation with hammering” 

action, the diamond core bit may be damaged.

When performing diamond core drilling operations, 
always set the change lever to the   position to use 

"rotation only" action.

Disposing of dust

Optional accessory

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before carrying out any work on the tool.

CAUTION:

Be sure to wear dust mask when 

disposing of dust.

CAUTION:

Empty the dust case regularly 

before the dust case becomes full.

 Failure to do so 

may decrease the dust collection performance and 

cause dust inhalation.

CAUTION:

The performance of dust collection 

decreases if the filter in the dust case become 

clogged. Replace the filter with new one after 

approximately 200 times of dust fulfillment as a 

guide.

 Failure to do so may cause dust inhalation.

1.

Remove the dust case while pressing down the 

lever of the dust case.

► 

Fig.35:

1.

 Lever

2.

Open the cover of the dust case.

► 

Fig.36:

1.

 Cover

3.

  Dispose of the dust, and then clean the filter.

► 

Fig.37

NOTICE:

When cleaning the filter, do not touch 

the filter with brush or similar, or blow com

-

pressed air on the filter. It may damage the filter.

Blow-out bulb

Optional accessory

After drilling the hole, use the blow-out bulb to clean the 

dust out of the hole.

► 

Fig.38

Using dust cup set

Optional accessory

Fit the dust cup set against the ceiling when operating 

the tool.

► 

Fig.39

NOTICE:

Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust 

cup set due to the heat produced by small metal 

dust or similar.

NOTICE:

Do not install or remove the dust cup 

set with the drill bit installed in the tool. It may 

damage the dust cup set and cause dust leak.

WIRELESS ACTIVATION 

FUNCTION

Optional accessory for DHR282/DHR283

What you can do with the wireless 

activation function

The wireless activation function enables clean and com-

fortable operation. By connecting a supported vacuum 

cleaner to the tool, you can run the vacuum cleaner 

automatically along with the switch operation of the tool.

► 

Fig.40

To use the wireless activation function, prepare follow-

ing items:
• 

A wireless unit (optional accessory)

• 

A vacuum cleaner which supports the wireless 

activation function

The overview of the wireless activation function 

setting is as follows. Refer to each section for detail 

procedures.

1.

Installing the wireless unit

2.

Tool registration for the vacuum cleaner

3.

Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION:

Place the tool on a flat and stable 

surface when installing the wireless unit.