Makita DHR282ZJ - Инструкция по эксплуатации - Страница 12

12 ENGLISH

7. 

In cold weather or when the tool has not been 

used for a long time, let the tool warm up for 

a while by operating it under no load. This 

will loosen up the lubrication. Without proper 

warm-up, hammering operation is difficult.

8. 

Always be sure you have a firm footing. Be 

sure no one is below when using the tool in 

high locations.

9. 

Hold the tool firmly with both hands.

10. 

Keep hands away from moving parts.

11. 

Do not leave the tool running. Operate the tool 

only when hand-held.

12. 

Do not point the tool at any one in the area 

when operating. The bit could fly out and 

injure someone seriously.

13. 

Do not touch the bit, parts close to the bit, or 

workpiece immediately after operation; they 

may be extremely hot and could burn your 

skin.

14. 

Some material contains chemicals which may 

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier 

safety data.

15. 

Always be sure that the tool is switched 

off and the battery cartridge and the bit are 

removed before handing the tool to other 

person.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using 

battery.

2. 

Do not disassemble battery cartridge.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them 

out with clear water and seek medical atten-

tion right away. It may result in loss of your 

eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store the tool and battery cartridge in 

locations where the temperature may reach or 

exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 

to the Dangerous Goods Legislation require-

ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack-

aging and labeling must be observed. 

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

Follow your local regulations relating to dis-

posal of battery.

12. 

Use the batteries only with the products 

specified by Makita.

 Installing the batteries to 

non-compliant products may result in a fire, exces

-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will 

also void the Makita warranty for the Makita tool and 

charger.

Tips for maintaining maximum 

battery life

1. 

Charge the battery cartridge before completely 

discharged. Always stop tool operation and 

charge the battery cartridge when you notice 

less tool power.

2. 

Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery 

service life.

3. 

Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let 

a hot battery cartridge cool down before 

charging it.

4. 

Charge the battery cartridge if you do not use 

it for a long period (more than six months). 

Important safety instructions for 

wireless unit

1. 

Do not disassemble or tamper with the wire-

less unit.

2. 

Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical 

attention immediately.

3. 

Use the wireless unit only with Makita tools.

4. 

Do not expose the wireless unit to rain or wet 

conditions.