Makita DHR182ZWJ - Инструкция по эксплуатации - Страница 22

22 ENGLISH

Troubleshooting for wireless activation function

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, 

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-

ment parts for repairs.

State of abnormality

Probable cause (malfunction)

Remedy

The wireless activation lamp does 

not light/blink.

The wireless unit is not installed into the tool. 

The wireless unit is improperly installed 

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or 

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the 

wireless unit and clean the slot.

The wireless activation button on the 

tool has not been pushed.

Push the wireless activation button on the tool 

briefly.

The stand-by switch on the vacuum 

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to 

"AUTO".

No power supply

Supply the power to the tool and the vacuum cleaner.

Cannot finish tool registration / can

-

celling tool registration successfully.

The wireless unit is not installed into the tool. 

The wireless unit is improperly installed 

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or 

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the 

wireless unit and clean the slot.

The stand-by switch on the vacuum 

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to 

"AUTO".

No power supply

Supply the power to the tool and the vacuum cleaner.

Incorrect operation

Push the wireless activation button briefly and perform 

the tool registration/cancellation procedures again.

The tool and vacuum cleaner are away 

from each other (out of the transmission 

range).

Get the tool and vacuum cleaner closer to each other. The 

maximum transmission distance is approximately 10 m 

however it may vary according to the circumstances.

Before finishing the tool registration/cancellation;

- the switch trigger on the tool is pulled or; 

- the power button on the vacuum 

cleaner is turned on.

Push the wireless activation button briefly and 

perform the tool registration/cancellation procedures 

again.

The tool registration procedures for the 

tool or vacuum cleaner have not finished.

Perform the tool registration procedures for both the 

tool and the vacuum cleaner at the same timing.

Radio disturbance by other appliances 

which generate high-intensity radio 

waves.

Keep the tool and vacuum cleaner away from the 

appliances such as Wi-Fi devices and microwave 

ovens.

The vacuum cleaner does not run 

along with the switch operation of 

the tool.

The wireless unit is not installed into the tool. 

The wireless unit is improperly installed 

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or 

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the 

wireless unit and clean the slot.

The wireless activation button on the 

tool has not been pushed.

Push the wireless activation button briefly and make 

sure that the wireless activation lamp is blinking in blue.

The stand-by switch on the vacuum 

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to 

"AUTO".

More than 10 tools are registered to the 

vacuum cleaner.

Perform the tool registration again. 

If more than 10 tools are registered to the vacuum 

cleaner, the tool registered earliest will be cancelled 

automatically.

The vacuum cleaner erased all tool 

registrations.

Perform the tool registration again.

No power supply

Supply the power to the tool and the vacuum cleaner.

The tool and vacuum cleaner are away 

from each other (out of the transmission 

range).

Get the tool and vacuum cleaner closer each other. The 

maximum transmission distance is approximately 10 m 

however it may vary according to the circumstances.

Radio disturbance by other appliances 

which generate high-intensity radio 

waves.

Keep the tool and vacuum cleaner away from the 

appliances such as Wi-Fi devices and microwave 

ovens.

The vacuum cleaner runs while the 

tool's switch trigger is not pulled.

Other users are using the wireless 

activation of the vacuum cleaner with 

their tools.

Turn off the wireless activation button of the other 

tools or cancel the tool registration of the other 

tools.