Bosch AQT 33-10 - Инструкция по эксплуатации - Страница 12

12

 | English 

F 016 L70 993 | (30.7.14)

Bosch Power Tools

Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest Bosch 
Service Centre.

WARNING! Inadequate extension cables can 
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.

Cable connections should be kept dry and off the ground.
For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch 
Service Centre.
For products 

not sold in GB

:

WARNING:

 For your safety, it is required that the plug at-

tached to the machine is connected with the extension cord. 
The coupling of the extension cord must be protected against 
splash water, be made of rubber or coated with rubber. The 
extension cord must be used with a cable strain relief.

Products sold in GB only

: Your product is fitted with an 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.
To prevent damage to the appliance, do not allow it to operate 
dry.

Operation

Starting

Attach water supply hose (not supplied) to the mains water 
supply and machine.
Connect the product to the mains supply ensuring that the 
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and water 
supply hose. Release trigger. Press the safety lock (front but-
ton on the gun handle).
Turn button on main switch. Point the power gun downwards. 
Press the trigger safety lock to release the trigger. Fully press 
the trigger.

Autostop function

The machine is designed to switch off the motor when the trig-
ger is released on the gun.

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the 
pressure washer by pulling the hose, this could cause the ma-
chine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure 
hose. Do not expose the high pressure hose to sharp edges or 
corners.

Never use a roto nozzle to clean motor vehicles.

Working advice for cleaning with detergents



Only use cleaning agents suitable specifically for high 
pressure washers.

We recommend that you use detergent sparingly for the sake 
of the environment. Observe the recommended dilution on 
the detergent label.

Recommended cleaning method

Step 1: Loosening dirt

Remove the nozzle from the lance to give a low pressure flow 
and spray on the detergent sparingly. 

Step 2: Removing dirt

Spray off the loosened dirt with the high-pressure spray.

Note: 

When cleaning a vertical surface spray off dirt/deter-

gent from the bottom and work in an upwards direction. Rinse 
from the top and work downwards.

Use with alternative water sources

This high-pressure washer will self prime and can draw water 
from water tanks and natural water sources. It’s 

IMPORTANT

that the water is clean and the BOSCH inlet filter is clear and 
fitted to the machine. 

Open tanks/containers and natural water sources 

Use the Self Priming accessory kit comprising:
– Inlet strainer with non return valve

– 3 m  reinforced  supply  hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m 
above the water level in the source in approximately 15 sec-
onds. 

Submerge the 3 m hose in water to displace the air. Connect 
the 3 m supply hose to the pressure washer ensuring that the 
inlet strainer remains submerged in the water source.

Run the pressure washer with the gun disconnected until a 
steady flow of water appears from the high pressure hose. 
Stop if this has this has not been achieved within 25 seconds 
and check all the connections. Switch off and connect the 
gun, lance and nozzle to operate. 

It is important to ensure that all hose and coupling connec-
tions are of good quality, air tight and that all washers are in 
good condition and correctly seated in place. Failure to do so 
may affect the self priming performance.

OBJ_BUCH-1870-006.book  Page 12  Wednesday, July 30, 2014  8:42 AM