Материнские платы GIGABYTE GA 945G DS3 rev 3 3 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
GA-945G-DS3 Motherboard
- 36 -
English
2-3
Integrated Peripherals
On-Chip Primary
/Secondary
PCI IDE
Enabled
Enable onboard 1st
/2nd
channel IDE port. (Default value)
Disabled
Disable onboard 1st
/2nd
channel IDE port.
On-Chip SATA Mode
Disabled
Disable this function.
Auto
BIOS will auto detect. (Default value)
Combined
Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on the
motherboard; 2 for SATA and the other for PATA.
Enhanced
Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6 HDDs
to use; 4 for SATA and the other for PATA.
Non-Combined
Set On-Chip SATA mode to Non-Combined, SATA will be simulated to
PATA mode. Support a maximum of 4 SATA devices. PATA devices will be
ignored.
PATA IDE Set to
Ch.0 Master/Slave Set PATA IDE to Ch. 0 Master/Slave. (Default value)
Ch.1 Master/Slave Set PATA IDE to Ch. 1 Master/Slave.
SATA Port 0/2 Set to
This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".
If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.
SATA Port 1/3 Set to
This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".
If PATA IDE were set to Ch. 0 Master/Slave, this function will auto set to Ch. 1 Master/Slave.
USB Controller
Enabled
Enable USB controller. (Default value)
Disabled
Disable USB controller.
CMOS Setup Utility-Copyright (C) 1984-2007 Award Software
Integrated Peripherals
On-Chip Primary PCI IDE
[Enabled]
On-Chip Secondary PCI IDE
[Enabled]
On-Chip SATA Mode
[Auto]
x PATA IDE Set to
Ch.0 Master/Slave
SATA Port 0/2 Set to
Ch.2 Master/Slave
SATA Port 1/3 Set to
Ch.3 Master/Slave
USB Controller
[Enabled]
USB 2.0 Controller
[Enabled]
USB Keyboard Support
[Disabled]
USB Mouse Support
[Disabled]
Legacy USB storage detect
[Enabled]
Azalia Codec
[Auto]
Onboard H/W LAN
[Enabled]
`
SMART LAN
[Press Enter]
OnBoard LAN Boot ROM
[Disabled]
Onboard Serial Port 1
[3F8/IRQ4]
Onboard Parallel Port
[378/IRQ7]
Parallel Port Mode
[SPP]
x ECP Mode Use DMA
3
KLJI
: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Item Help
Menu Level
`
