STANLEY FatMax DST 10186 100552280 - Инструкция по эксплуатации - Страница 18

G

B

18

1. 

PRECAUTIONS

An ACOUSTIC PRESSURE value of 4 m. corresponds 

to the ACOUSTIC POWER value stated on the label 

located on the compressor, minus 20 dB.

  THINGS TO DO  

●

The compressor must be used in a suitable 

environment (well ventilated with an ambient 

temperature of between +5°C and +40°C) and never 

in places affected by dust, acids, vapors, explosive 

or flammable gases.

●

Always maintain a safety distance of at least 4 meters 

between the compressor and the work+ area.

●

Any coloring of the belt guards of the compressor during 

painting operations indicates that the distance is too short.

●

Insert the plug of the electric cable in a socket of suitable 

shape,  voltage  and  frequency  complying  with  current 

regulations.

● Use extension cables with a maximum length of 5 meters 

and of suitable cross-section.

●

The use of extension cables of different length and also 

of adapters and multiple sockets should be avoided.

●

Always use the switch 

I/O

 to switch off the compressor.

● Always use the handle to move the compressor.

● When  operating,  the  compressor  must  be  placed  on  a 

stable, horizontal surface.

  THINGS 

NOT

 TO DO  

● Never direct the jet of air towards persons, animals or your 

body. (Always wear safety goggles to protect your eyes 

against flying objects that may be lifted by the jet of air).

● Never direct the jet of liquids sprayed by tools connected 

to the compressor towards the compressor.

● Never use the appliance with bare feet or wet hands or feet.

●

Never pull the power cable to disconnect the plug from 

the socket or to move the compressor.

●

Never leave the appliance exposed to adverse weather 

conditions.

●

Never transport the compressor with the receiver under 

pressure.

● Do not weld or machine the receiver. In the case of faults 

or rusting, replace the entire receiver.

● Never allow inexperienced persons to use the compressor. 

Keep children and animals at a distance from the work 

area.

●

This appliance is not intended for use by persons 

(including  children)  with  reduced  physical,  sensory  or 

mental capabilities, or lack of experience and knowledge.

●

Children should be supervised to ensure that they do not 

play with the appliance.

● Do not position flammable or Nylon®/fabric objects closed 

to and/or on the compressor.

● Never  clean  the  compressor  with  flammable  liquids  or 

solvents. Check that you have unplugged the compressor 

and clean with a damp cloth only.

● The compressor must be used only for air compression. 

Do not use the compressor for any other type of gas.

●

The compressed air produced by the compressor cannot 

not be used for pharmaceutical, food or medical purposes 

except after particular treatments and cannot be used to 

fill the air bottles of scuba divers.

● Pay attention to the work being carried out. Use  common 

sense. Do not stand on the compressor. Do not allow the 

compressor to operate unattended.

  THINGS YOU SHOULD KNOW  

● To  avoid  overheating  of  the  electric  motor,

 this 

compressor is designed for intermittent operation 

as indicated on the technical dataplate

 (for example, 

S3 50 % means 5 minutes ON, 5 minutes OFF). In the 

case of overheating, the thermal cutout of the motor trips, 

automatically cutting off the power when the temperature 

is too high. The motor restarts automatically when normal 

temperature conditions are restored.

● The compressor is equipped with a solenoid valve that 

allows air to be vented from the head, so as to facilitate 

the next restart of the compressor. Therefore, it is normal 

to feel vented air for a few seconds, when the compressor 

reaches  the  cut-off  pressure  (set  by  the  manufacturer 

during the testing phase). The same phenomenon occurs 

even when the compressor is switched off.

● After switching off the compressor, you must wait three 

seconds before switching on the machine again.

● All  the  compressors  are  fitted  with  a  safety  valve  that 

is tripped in the case of malfunctioning of the pressure 

switch in order to assure machine safety.

  The safety valve is set to avoid over-pressurization of 

the  air  tanks.  This  valve  is  factory  pre-set  and  will  not 

function unless tank pressure reaches this pressure. Do 

not attempt to adjust or eliminate this safety device.

  Any adjustments to this valve could cause serious injury. 

If  this  device  requires  service  or  maintenance,  see  an 

Authorized Service Center.

●

The red notch on the pressure gauge refers to the 

maximum  operating  pressure  of  the  tank.  It  does  not 

refer to the adjusted pressure.

● When  fitting  a  tool,  the  flow  of  air  in  output  must  be 

switched off.

● When using compressed air, you must know and comply 

with the safety precautions to be adopted for each type of 

application (inflation, pneumatic tools, painting, washing 

with water-based detergents only, etc.).

●

Please check that the air consumption and the maximum 

working pressure of the pneumatic tool and connection 

pipes (with the compressor) to be used, are compatible 

with the pressure set on the pressure regulator and with 

the amount of air supplied by the compressor.

Preserve this handbook for future reference.