Krups EA8005PE Espresseria Automatic - Инструкция по эксплуатации - Страница 10

17

EN

16

BEVERAGE PREPARATION

TYPES OF 

COFFEE

Number of cups

possible

Possible volume 

settings (ml) 

Possible strength 

settings

RISTRETTO

1

20 to 30 ml 

 or 

2 x 1

2 x 20 to 30 ml

in two cycles

ESPRESSO

1

30 to 70 ml 

 or 

2 x 1

2 x 30 to 70 ml

in two cycles

COFFEE or LUNGO 

1

80 to 220 ml 

 or 

2 x 1

2 x 80 to 220 ml

in two cycles

BEFORE FIRST USE

Preparing the appliance

Pull out and fill the water tank - 

Fig. 1 and 2

.

Put it back in place by pressing firmly and close the lid again - 

Fig. 3

. 

Open the coffee bean container lid. Add the coffee beans - 

Fig. 4

.

Close the coffee bean container lid again.

Do not fill the water tank with hot water, milk or any other liquid.

 If you turn on the appliance when the water 

tank is not in place or not correctly filled (under the “min.” level,), the 

 light will come on and making an espresso 

or a cup of coffee will be made impossible.

 NEVER PUT GROUND COFFEE IN THE COFFEE CONTAINER.

It is recommended that you do not use oily, caramelised or flavoured coffee beans for this appliance. These kinds of 

beans may damage the appliance.

Check that the coffee beans do not contain any foreign particles such as grit, as any damage caused by the presence 

of foreign particles will invalidate the guarantee.

Do not put water into the coffee bean container.

Remember to fit the drip tray to avoid waste water flowing onto the work surface and staining it or scalding you.

Check that your water tank is clean.

Initialisation cycle - total duration: around 3 minutes

Turn on the appliance by pressing the button 

 - 

Fig. 5

. The light 

 is constant.

Put a container with a minimum capacity of 0.6 litres underneath the two coffee outlets and steam nozzle.

Press the 

 - 

Fig. 6

 button: the appliance starts the initialisation cycle for rinsing of the steam and coffee circuits. The 

light 

 flashes.

The cycle is finished when the light 

 becomes constant. The appliance is now ready to use.

It is preferable to rinse the 2 circuits out at least once after the appliance has not been used for several days. Each 

time you plug your appliance in, it will carry out an initialisation cycle.

Preparing the grinder

You can choose the strength of your coffee by setting the coffee bean grinding fineness. The finer the grinding setting, 

the stronger and creamier the coffee should be. Set the desired fineness for grinding by turning the ‘Grinding fineness 

setting’ knob.Turn to the left for finer grind. Turn to the right for coarser grind.

 CHANGE THE SETTING DURING GRINDING.

Never force the grinding fineness setting button.

PREPARING ESPRESSO AND LONG COFFEES

YOUR APPLIANCE IS DESIGNED TO MAKE COFFEE FROM COFFEE BEANS ONLY.

When you first make coffee with the appliance or after a long period of absence or a cleaning or scale removal 

procedure, a little steam and hot water will come out of the steam nozzle (priming).

Splashing or scalding may occur if the coffee outlets are set too high in relation to the size of the cups.

Note:

The amount of water needed to make an espresso is between 30 and 70 ml.

The amount of water needed to make a coffee is between 80 and 220 ml.

Production of an espresso or coffee

Plug in your appliance.

Press the button 

. The light will flash during the pre-heating and initialisation cycle.

The light 

 becomes constant.

Put a cup under the coffee outlets. You can lower or raise the coffee outlets to suit the size of your cups - 

Fig. 7

.

Select the 

 key to get a strong espresso or the 

 key to get a standard espresso - 

Fig. 8

.

You can change the volume of water at any time - 

Fig. 9

.

To stop coffee flowing into the cup, you can either again press one of the 

 or 

, keys or turn the knob to the min. 

position.

The ground coffee is moistened with a little hot water after the grinding stage. A few moments later, percolation as 

such starts. Beyond a certain amount of coffee in the cup, we recommend - in order to obtain a stronger coffee - to 

divide your preparation into two separate cycles. Example 2 x 70 ml cycles for a cup of 140 ml.

2 cup function

You can prepare 2 cups of coffee or espresso with your appliance.

Press the button 

 the light flashes during the pre-heating of the appliance 

The light 

 becomes constant.

Place 2 cups under the coffee outlets. You can lower or raise the coffee outlets to suit the size of your cup

 - Fig. 10

.

Select the button 

 or 

 according to your choice, by quickly pressing the button twice. The light 

 comes on with a 

double flash to inform you that you have requested two cups of coffee.

The appliance will automatically sequence 2 complete coffee-making cycles. 

Make sure that you don’t remove the cups after the first cycle.

If you press the 

 button once and the 

 button a second time (or the other way round), the second one isn’t taken 

into account.

PREPARING STEAM

Steam froths up the milk to make a cappuccino or a caffe latte, for example, and also heats up liquids. As you need a 

higher temperature to produce steam than to make an espresso, the appliance runs an additional pre-heating phase for 

steam.

Plug in your appliance.

Press the 

 button: the light flashes during the pre-heating of the appliance.

The light 

 becomes constant.

Press the button 

 - Fig. 11

.

The light 

 flashes during the pre-heating.

Once the pre-heating is finished, the light 

 stays constant and you can start the steam production by pressing the 

button again.

Press the 

 button again to stop the cycle.

The appliance goes back to its initial position if the steam control is not used after 2 mins.

 BE CAREFUL, BECAUSE THE CYCLE DOES NOT STOP IMMEDIATELY.