Liebherr CBesf 4006 BioFresh - Инструкция по эксплуатации - Страница 9

19

You may be able to rectify the following faults by checking the 

possible causes yourself:

appliance does not work, display is unlit

-  Is the appliance switched on properly?

-  Is the mains plug properly inserted in the socket?

-  Is the socket fuse intact?

-  Is the refrigerator compartment switched on?

-  Has the door been open for more than 15 minutes?

-  The bulb is defective. Change the bulb as described in 

"Interior light".

The interior light does not come on

-   Is the appliance standing firmly on the floor, or does the 

compressor cause nearby items of furniture or objects to 

vibrate? If necessary, move the appliance slightly, align by 

adjusting the adjustable feet, or move bottles and contai-

ners apart.

-  The following are normal: 

flow noises

, bubbling or drip-

ping noises, they come from the refrigerant flowing in the 

refrigerant circuit.

  A short 

clicking sound

: This will be heard whenever the 

refrigeration unit (the motor) switches on or off automatically. 

Motor noise

: This will be slightly louder for a brief period 

when the refrigeration unit switches on.

Temperature is not low enough

-  Have you put too much fresh food into the freezer 

without

activating SuperFrost? (See "SuperFrost")

-  Does the door close properly?

-  Is the appliance sufficiently well ventilated?

  Clear ventilation grilles if necessary.

-  Is the ambient temperature too hot?  

(See "Safety regulations")

-   Has the appliance been opened too often or left open too 

long? 

-  If applicable, wait until the appliance reaches the required 

temperature itself.

appears in the display

-   A power failure/interruption has occurred,  proceed accor-

ding to the section "Power failure- / FrostControl-display".

Loud running noise

Customer service and type plate

If none of the above causes apply and you cannot rectify the 

fault yourself, or if "

F 0

" to " 

F 5

" appears in the temperature 

display, this means that a fault has occurred. In this case, 

please contact your nearest service centre (see attached list). 

Inform the service centre of the 

display

 number, the 

  type designation 

1

  service number 

2

and 

  appliance number 

3

of the type plate. This enables rapid, 

specific service.  The type plate is 

located inside the appliance on the 

left-hand side.

Leave the appliance shut until the 

customer service engineer arrives so 

as to prevent any further cold loss.

The manufacturer is continually working on the continous 

improvement of all types and models. We therefore hope for 

your understanding that we reserve the right to alter design, 

equipment and technology without notice.

Troubleshooting

The compressor will continue to run for a while

-  On energy saving models, this is caused by the functions 

and is perfectly normal. When less refrigeration is required, 

the VCC compressor switches to a low speed. It will then 

be running almost constantly, but it does save energy.

Insertion into row of kitchen units 

The appliance can be integrated into the kitchen units. To 

adapt the appliance to the height of the row of kitchen units, a 

suitable top cupboard can be fitted above the appliance 

1

.

For ventilation and air extraction, an exhaust air shaft at least 

50 mm deep must be provided on the rear of the top cupboard 

over the entire width of the cupboard. The ventilation cross-

section below the ceiling of the room should be at least 300 

cm

2

. Generally, the bigger the cross section, the more eco-

nomically the appliance operates.

W

  When integrating with standard kitchen units (depth 

max. 580 mm) and decor panels of up to max. 2 mm thick, 

the appliance can be installed directly next to the kitchen 

unit. The door of the appliance protrudes beyond the front 

of the kitchen unit 34 mm at the side and 51 mm in the cen-

tre of the appliance. This allows it to be opened and closed 

easily.

W

  When installing the appliance next to a wall 

4

, a distance 

on the hinge side of min. 36 mm is required between the 

appliance and the wall (handle projection with door open).

  1 

top cupboard 

3 

side of kitchen unit

  2 

refrigerator freezer 

4 

wall