Briggs&Stratton Sprint 2200A MBK0016082 - Инструкция по эксплуатации - Страница 6

Not for 

Reproduction

6 BRIGGSandSTRATTON.COM

Step 4: Connecting Electrical Loads   Figure

1

Use only high quality, well-insulated extension cables in 

accordance with IEC 245-4 with the generator’s 230 Volt 

AC outlets. Inspect extension cables before each use. 

Check that all extension cables are suitably rated and 

are not damaged. When using extension cords under 40° 

C, the total length of cords for a cross section of 1.5 mm² 

should not exceed 50 m or for a cross section of 2.5 mm² 

should not exceed 80 m.

WARNING! 

  Damaged or overloaded extension 

cords could overheat, arc, and burn resulting in 

death or serious injury. Electrical equipment, 

including cables and plug connections, should not be 

defective. 

NOTICE

 Ensure main breaker (

D

) (6200A ONLY) is in 

ON (I) position. Connect electrical loads in off position 

then turn on for operation. 

230 Volt AC, 16 Amp, Schuko Receptacle

Use receptacle (

E

) to operate 230 Volt AC, single-phase, 

50 Hz electrical loads. The receptacle is protected 

against overload by a push-to-reset circuit breaker (

C

).

Protection of electrical components depends on circuit 

breakers specifically matched to the generator. Replace 

circuit breaker with identical rating and performance 

characteristics.

WARNING! 

  Generator voltage could cause 

electrical shock or burn resulting in death or 

serious injury. Use a residual-current device 

(RCD) in any damp or highly conductive area, such as 

metal decking or steel work. Do not touch bare wires or 

receptacles. Do not use generator with electrical cords 

which are worn, frayed, bare or otherwise damaged. Do 

not operate generator in the rain or wet weather. Do not 

handle generator or electrical cords while standing in 

water, while barefoot, or while hands or feet are wet. Do 

not allow unqualified persons or children to operate or 

service generator. Keep children a safe distance from 

generator.

Step 5: Generator Shut Down

  1.  Turn off and unplug all electrical loads from generator 

panel receptacles. Never  stop engine with electrical 

devices plugged in and turned on.

  2.  Let engine run at no-load for one minute to stabilize 

internal temperatures of engine and generator.

  3.  Push engine switch to OFF (0) position.

  4.  Rotate fuel valve to OFF (0) position.

Maintenance

Maintenance Schedule

Follow hourly or calendar intervals, whichever occurs 

first. More frequent service is required when operating in 

adverse conditions.

1

  Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve performance and 

extend the life of the outdoor generator. See any Briggs 

& Stratton Authorized Service Dealer for service. 

Installation and major repair work should only be 

performed by specifically trained personnel.

The generator’s warranty does not cover items that have 

been subjected to operator abuse or negligence. To 

receive full value from the warranty, the operator must 

maintain the generator as instructed in this manual.

All service and adjustments should be made at least 

once each season. A new spark plug and clean air filter 

assure proper fuel-air mixture and help your engine 

run better and last longer. Follow requirements in 

Maintenance Schedule

.

 WARNING  

 To ensure machine safety, use only 

original spare parts from the manufacturer or approved 

by the manufacturer. Should you have questions about 

replacing components on your generator, please visit our 

website at 

BRIGGSandSTRATTON.COM

.

First 5 Hours

  •  Change engine oil

Every 8 Hours or Daily

  •  Clean debris
  •  Check engine oil level

Every 25 Hours or Yearly

  •  Clean engine air filter

1

Every 50 Hours or Yearly

  •  Change engine oil

1

Yearly

  •  Replace engine air filter

1 

  •  Service fuel valve
  •  Service spark plug
  •  Inspect muffler and spark arrester
  •  Clean cooling system

1