SKIL F0150780RA - Инструкция по эксплуатации - Страница 11

11

proper precautions are taken; do not let go of the chain 

saw)

- 

do not over reach and do not cut above shoulder 

height

 (this helps prevent unintended tip contact and 

enables better control of the chain saw in unexpected 

situations)

- 

only use replacement bars and chains specified 

by the manufacturer

 (incorrect replacement bars 

and chains may cause chain breakage and/or 

kickback)

- 

follow the manufacturer’s sharpening and 

maintenance instructions for the saw chain

(decreasing the depth gauge height can lead to 

increased kickback)

PERSONAL SAFETY

•  It is recommended that the irst time user should have 

practical instruction in the use of the chainsaw and the 

protective equipment from an experienced operator and 

that the initial practice should be cutting logs on a saw 
horse or cradle

•  Do not touch rotating chain

•  Do not operate chain saw near other people, 

children or animals

•  Do not operate chain saw after drinking alcohol or 

under the influence of intoxicating drugs or 

medication

•  This tool is not intended for use by persons (including 

children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless 

they have been given supervision or instruction 

concerning use of the tool by a person responsible for 

their safety

•  Ensure that children do not play with the tool

ElECTRICAl SAFETY

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool

•  Connect the tool via a fault current (FI) circuit breaker 

with a triggering current of 30 mA maximum

•  Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

•  Only use an extension cord which is intended for outdoor 

use and equipped with a watertight plug and coupling-
socket

•  Only use extension cords with a maximum length of 20 

metres (1,5 mm²) or 50 metres (2,5 mm²)

•  Always switch of tool and disconnect plug from power 

source if the power supply cord or the extension cord is 

cut, damaged or entangled (

do not touch the cord 

before disconnecting the plug

)

•  Protect the (extension) cord from heat, oil and sharp 

edges

•  Never use the cord for carrying, pulling or unplugging the 

tool

•  Inspect the cord periodically and have it replaced by a 

qualiied person, if damaged

•  Inspect the extension cord periodically and replace it, if 

damaged (

inadequate extension cords can be 

dangerous

)

•  Do not use the tool if the switch does not turn it on and 

of; always have a damaged switch repaired by a qualiied 

person

EXPLANATION OF SYMBOLS ON TOOL

3

 Read the instruction manual before use

4

 Always switch off tool and disconnect plug from 

power source if the power supply cord or the 

extension cord is cut, damaged or entangled (do not 

touch the cord before disconnecting the plug

)

5

 Do not expose tool to rain

6

 Wear protective glasses and hearing protection

7

 Double insulation (no earth wire required)

8

 Do not dispose of the tool together with household waste 

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut of the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  Assembly 

9

!  do not connect the chain saw to mains before it is 

completely assembled

!  always use gloves when handling the chain

-  place the chain saw on any suitable lat surface

-  remove cover plate A by turning locking knob B 

counter-clockwise

-  slide chain C in the slot around chain bar D

!  ensure chain is in correct running direction by 

comparing with chain symbol E

-  it the chain onto drive sprocket F and guide chain bar 

D, so that fastening bolt G and the two guide ins H it 

into the keyway of chain bar D, and that chain 

tensioning peg J its into the respective hole of chain 

bar D

-  if necessary, turn tensioning knob K to bring tensioning 

peg J in alignment with the hole in chain bar D

-  check if all parts are seated properly and hold chain 

and chain bar in a level position

-  turn tensioning knob K until all the slack is taken up in 

the chain

-  mount cover plate A as illustrated

-  tighten locking knob B on fastening bolt G by turning it 

clockwise

•  Tensioning chain 

0

-  place the chain saw on any suitable lat surface

-  check if the chain links are correctly located in the slot 

around chain bar D

1)   loosen locking knob B until it is just holding chain bar 

in position (

do not remove

)

2)  lift the chain bar somewhat and hold it in that position

3)   turn chain tensioning knob K upwards until the lowest 

chain links come up and JUST touch the bottom of 

chain bar D

4)  tighten locking knob B by turning it clockwise

5)  release chain bar

6)   the correct chain tension is reached when the chain 

can be raised approx. 4 mm from the chain bar in the 

centre

!  always check the chain tension before use, after 

the first cuts and regularly during use (approx. 

every 10 minutes)

-  upon initial operation, new chains can lengthen 

considerably