SKIL F0150780RA - Инструкция по эксплуатации - Страница 10

10

g) 

If devices are provided for the connection of dust 

extraction and collection facilities, ensure these are 

connected and properly used.

 Use of dust collection 

can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) 

Do not force the power tool. Use the correct power 

tool for your application.

 The correct power tool will do 

the job better and safer at the rate for which it was 

designed.

b) 

Do not use the power tool if the switch does not turn 

it on and off.

 Any power tool that cannot be controlled 

with the switch is dangerous and must be repaired.

c) 

Disconnect the plug from the power source and/or 

the battery pack from the power tool before making 

any adjustments, changing accessories, or storing 

power tools.

 Such preventive safety measures reduce 

the risk of starting the power tool accidentally.

d) 

Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained 

users.

e) 

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f) 

Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control.

g) 

Use the power tool, accessories and tool bits etc., in 

accordance with these instructions, taking into 

account the working conditions and the work to be 

performed.

 Use of the power tool for operations diferent 

from those intended could result in a hazardous situation.

5) SERVICE

a) 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is maintained.

CHAIN SAW SAFETY WARNINGS

• 

Children and juveniles, with the exception of 

apprentices older than 16 years and under 

supervision, may not operate the chain saw. The 

same applies for persons who do not or do not 

sufficiently know how to handle the chain saw.

 The 

operating instructions should always be ready to hand. 

Persons unit or tired must not operate the chain saw.

• 

Keep all parts of the body away from the saw chain 

when the motor is operating. Before you start the 

saw, make sure the saw chain is not contacting 

anything.

 A moment of inattention while operating chain 

saws may cause entanglement of your clothing or body 

with the saw chain.

• 

Always hold the chain saw with your right hand on 

the rear handle and your left hand on the front 

handle.

 Holding the chain saw with a reversed hand 

coniguration increases the risk of personal injury and 

should never be done.

• 

Hold the power tool by insulated gripping surfaces 

only, because the saw chain may contact hidden 

wiring or its own cord.

 Saw chains contacting a “live” 

wire may make exposed metal parts of the power tool 

“live” and could give the operator an electric shock.

• 

Wear safety glasses and hearing protection. Further 

protective equipment for head, hand, legs and feet 

is recommended.

 Adequate protective clothing will 

reduce personal injury by lying debris or accidental 

contact with saw chain.

• 

Do not operate a chain saw in a tree.

 Operation of a 

chain saw in a tree, may result in personal injury.

• 

Always keep proper footing and operate the chain 

saw only when standing on fixed, secure and level 

surface.

 Slippery or unstable surfaces such as ladders 

may cause a loss of balance or control of the chain saw.

• 

When cutting a limb that is under tension be alert 

for spring back.

 When the tension in the wood ibres is 

released the spring loaded limb may strike the operator 

and/or throw the chain saw out of control.

• 

Use extreme caution when cutting brush and 

saplings.

 The slender material may catch the saw chain 

and be whipped toward you or pull you of balance.

• 

Carry the chain saw by the front handle with the 

chain saw switched off and away from your body. 

When transporting or storing the chain saw, always 

fit the guide bar cover.

 Proper handling of the chain 

saw will reduce the likelihood of accidental contact with 

the moving saw chain.

• 

Follow instructions for lubricating, chain tensioning 

and changing accessories.

 Improperly tensioned or 

lubricated chain may either break or increase the chance 

for kickback.

• 

Keep handles dry, clean, and free from oil and 

grease.

 Greasy, oily handles are slippery causing loss of 

control.

• 

Cut wood only. Don’t use chain saw for purposes 

not intended (e.g. do not use chain saw for cutting 

plastic, masonry or non-wood building materials).

Use of the chain saw for operations diferent than 

intended could result in a hazardous situation.

CAUSES AND OPERATOR PREVENTION OF 

kICkBACk

•  Kickback may occur when the nose or tip of the guide bar 

touches an object, or when the wood closes in and 
pinches the saw chain in the cut

•  Tip contact in some cases may cause a sudden reverse 

reaction, kicking the guide bar up and back towards the 
operator

•  Pinching the saw chain along the top of the guide bar 

may push the guide bar rapidly back towards the operator

•  Either of these reactions may cause you to lose control of 

the saw which could result in serious personal injury (do 

not rely exclusively upon the safety devices built into your 

saw; as a chain saw user, you should take several steps 

to keep your cutting jobs free from accident or injury)

•  Kickback is the result of tool misuse and/or incorrect 

operating procedures or conditions and can be avoided 

by taking proper precautions as given below:

- 

maintain a firm grip, with thumbs and fingers 

encircling the chain saw handles, with both 

hands on the saw and position your body and 

arm to allow you to resist kickback forces

(kickback forces can be controlled by the operator, if