Ryobi RCS3835T 5133002386 - Инструкция по эксплуатации - Страница 9

7

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

Limbing a tree

See page 280.

Limbing is removing the branches from a fallen tree. When 
limbing leave larger lower limbs to support the log off the 
ground. Remove the small limbs in one cut. Branches 
under tension should be cut from the bottom up to avoid 
binding the product.

Cutting springpoles

See page 280.

A springpole is any log, branch, rooted stump, or sapling 
which is bent under tension by other wood so that it springs 
back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of 
springing back to the upright position during the bucking 
cut to separate the log from the stump. Watch out for 
springpoles—they are dangerous. Do not attempt to cut 
bent branches or stumps which are under tension unless 
you are professionally trained and competent to do so.

TRANSPORTATION AND STORAGE

Ŷ

Stop the engine, engage the chain brake, disconnect 
spark plug wire from the spark plug and allow it to cool 
before storing or transporting.

Ŷ

Clean all foreign material from the product.

Ŷ

Drain all fuel from tank into a container approved for 
petrol. Remember to properly replace and tighten the 
fuel mix cap.

Ŷ

Run the engine until it stops. This will remove all fuel-
lubricant mix that could become stale and leave varnish 
and gum in the fuel system.

Ŷ

Drain all bar and chain lubricant from tank into a 
container approved for lubricant. Remember to properly 
replace and tighten the chain lubricant cap.

Ŷ

Always fit guide bar cover before storing the product, or 
during transportation.

Ŷ

Store the product in a cool dry and well-ventilated 
place that is inaccessible to children. Keep away from 
corrosive agents such as garden chemicals and de-
icing salts. Do not store outdoors.

Ŷ

When carrying the product for short distance (from one 
working area to the next), always apply the chain brake 
so that the saw chain is restricted from movement.

Ŷ

When transporting the product, secure it against 
movement or falling to prevent injury to persons or 
damage to the product.

Ŷ

Never carry or transport the product while the engine 
is running.

Abide by all government and local regulations for the safe 
storage and handling of petrol. Excess fuel should be used 
in other 2-cycle engine powered equipment.

MAINTENANCE

Always keep the product in good working condition.

 WARNING

Use only original manufacturer’s replacement parts, 
accessories and attachments. Failure to do so can 
cause possible injury, poor performance and may void 
your warranty.

 WARNING

Servicing requires extreme care and knowledge 

DQG VKRXOG EH SHUIRUPHG RQO\ E\ D TXDOL¿HG VHUYLFH

technician. For servicing and repairs, you have to return 
the product to your nearest authorised service centre. 
When servicing, use only identical replacement parts.

 WARNING

Before inspecting, cleaning, or servicing the product, 
stop the engine, engage the chain brake, disconnect 
the spark plug wire from the spark plug. Failure to follow 
these instructions can result in serious personal injury or 
property damage.

Ŷ

You may only make adjustments or repairs described 
in this manual. For other repairs, contact the authorised 
service centre.

Ŷ

Consequences of improper maintenance may cause 
the chain brake and other safety features to not function 
correctly, thus increasing the potential for serious injury. 
Keep the product professionally maintained and safe.

Ŷ

Sharpening the chain safely is a skilled task. Therefore 
the manufacturer strongly recommends that a worn 
or dull  chain is replaced with a new one, available 
from your authorised service centre. The part number 
is available in the product specification table in this 
manual.

Ŷ

Follow instructions for lubricating and chain tension 
checking and adjustment.

Ŷ

After each use, clean the product with a soft dry cloth.

Ŷ

Check all nuts, bolts and screws at frequent intervals 
for security to ensure the product is in safe working 
condition. Any part that is damaged should be properly 
repaired or replaced by an authorised service centre.

REPLACING GUIDE BAR AND SAW CHAIN

See page 282 - 285.

1.  Stop the product. Wear protective gloves.
2.  Disengage the chain brake.
3.  Unscrew the guide bar locking knob and remove the 

sprocket cover.

4.  Remove the bar and saw chain from the product.
5.  Clean the underside of the sprocket.
6.  To replace the bar with a new one, loosen the screw of 

the chain tension assembly. Mount the chain tension 
assembly on to the new bar and tighten the screw.

7.  Attach the guide bar and chain tension assembly to the 

chain saw. Lower the guide bar so that the bolt goes 
through the hole in the bar and chain tension assembly.

8.  The saw chain should face in the direction of chain 

rotation. If they face backwards, turn the loop over.

9.  Place the loop around the drive sprocket. Then place