Ryobi RCS3835T 5133002386 - Инструкция по эксплуатации - Страница 6

4

| English

Ŷ

Loosen the fuel cap slowly.

Ŷ

Carefully pour the fuel mixture into the tank. Avoid 
spillage.

Ŷ

Prior to replacing the fuel cap, clean and inspect the 
gasket.

Ŷ

Immediately replace the fuel cap and hand tighten it. 
Wipe away any fuel spillage.

NOTE: It is normal for the engine to emit smoke during and 

DIWHUWKH¿UVWXVH

ADDING CHAIN LUBRICATING OIL

See page 273.

 WARNING

Never work without chain lubricant. If the saw chain is 
running without lubricant, guide bar and saw chain can 
be damaged. It is therefore essential to check the oil 
level frequently and every time before starting to use the 
product.

1. Clear surface around the oil cap to prevent 

contamination.

2.  Unscrew and remove the cap from the oil tank.
3.  Pour the oil into the oil tank and monitor the oil level 

gauge. Ensure that no dirt enters the oil tank while 
filling.

4.  Put the oil cap back on and tighten. Wipe away any 

spillage.

5.  One full oil tank will enable you to use the product for 

20- 40 min.

NOTE:

 A properly functioning chain and bar lubricating 

system will normally discharge oil from the chain during use. 
To check the functionality of the chain and bar lubricating 
system, point the tip of the chain at a light coloured surface, 
such as a newspaper. A distinct line of oil splatter should be 
observed after a short time.

Recommended chain lubricating oil

Ŷ

The manufacturer recommends you use only Ryobi 
chainsaw lubricating oil. (Available from your authorised 
service centre)

STARTING THE PRODUCT

Starting the product differs depending on whether the 
engine is cold or warm.

 WARNING

Keep your body to the left of the chain line. Never 
straddle the saw or chain, or lean over past the chain 
line.

Ŷ

Place the product on level ground and ensure that no 
objects or obstructions are in the immediate vicinity that 
could come in contact with the bar and chain.

Ŷ

Hold the front handle firmly with your left hand and put 
your right foot onto the base of the rear handle.

NOTE

: In the following starting instruction, when the choke 

lever is pulled all the way out to the “start “ position, the 
throttle is set for starting. To reset the throttle  to the “run“ 

position, squeeze and then release the throttle trigger.

To start a cold engine:

See page 272 - 273.

1.  Turn ignition switch to the “on“ position.
2.  Make sure the chain brake is in the brake position by 

pushing forward on the lever/hand guard.

3.  Fully press and release the primer bulb at least 10 

times.

4.  Pull choke lever all the way out to the “start“ position.
5.  When the temperature is above 10°C, pull the starter 

grip until the engine attempts to start, but no more than 
3 times. When the temperature is below 10°C, pull the 
starter grip until the engine attempts to start, but no 
more than 5 times.

6.  Push choke lever to the “half“ position. Pull starter grip 

until engine starts.

7.  Depress the trigger release and squeeze the throttle 

trigger, then release the throttle trigger to return the 
engine to idle.

8.  Allow the product to run idle for 15 - 30 seconds.
9.  Before accelerating the engine or cutting wood, make 

sure the chain brake is in the “

run

“ position by pulling 

back on the brake lever/hand guard.

 CAUTION

Failure to fully release the throttle when chain brake lever 
is in the brake position will result in serious damage to 
the product. Never squeeze and hold the throttle trigger 
while the chain brake is in the brake position.

To start a warm engine:

See page 281.

1.  Turn ignition switch to the “on“ position.
2.  Make sure the chain brake is in the brake position by 

pushing forward on the lever/hand guard.

3.  Press the primer bulb 10 times.
4.  Pull choke lever all the way out to the “start“ position 

and then push it back in the “run“ position.

5.  Pull starter grip until engine runs, but no more than 5 

times. Depress the trigger release and squeeze the 
throttle trigger, then release the throttle trigger to return 
the engine to idle. If engine does not start after 5 pulls, 
use cold engine starting procedure.

6.  Before accelerating the engine or cutting wood, make 

sure the chain brake is in the “run“ position by pulling 
back on the brake lever/hand guard.

SWITCHING BETWEEN OPERATING MODES

See page 287.

The product features an anti-freeze mode that prevents 
ice from forming inside the carburettor during operation in 

WHPSHUDWXUHVRI”ƒ&

A ventilation hatch on the right side of the air cleaner cover 
can be re-positioned to allow warm air to be supplied to the 
engine and prevents ice from forming inside the carburettor.