АТС Samsung NX-308 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
This MMC is used to changed trunk timer values. It is not advisable to change these
values, with exception of trunk flash time, without assistance from Technical Support.
The available options are and listed below:
DISPLAY
DESCRIPTION
RANGE
CLEARING
The interval for reuse of trunk after disconnecting a call.
0~25sec
(clearing time)
CO SUPV
C.O. checking
00~9000
(CO supervision time)
msec
F DGT DLY
After seizing a trunk line, system sends the first digit 1 0 0 ~ 2 5 0 0
(first digit delay time)
after this time.
ms
FLASH PBX
The duration of a flash when connected to a C.O. 1 0 0 ~ 2 5 0 0
(PBX flash time)
ms
MFS ON TM
The duration of DTMF Sender 'ON' status when 1 0 0 ~ 2 5 0 0
(MF sender on time)
sending DTMF signal.
ms
MF OFF TM
The interval of DTMF Sender 'OFF' when system 1 0 0 ~ 2 5 0 0
(MF sender off time)
sends DTMF signal.
ms
MPD DETCT
The minimum duration of MPD signal when the
40~500
(MPD detect time)
signal is incoming.
msec
NEW CALL
The duration of a flash sent to the central office to 100~9900
(New Call time)
disconnect the line.
ms
NO RING
if an incoming call is detected and is disconnected without
1~25sec
(no ring time)
call processing, the system and releases the C.O line.
PAUSE TM
This is a dialing pause duration timer. A pause is an
1~25sec
(pause time)
instruction for the system to wait.
RNG DETCT
Must be set shorter than the 'ON' cycle of a C.O. ring to prevent 100~2500
(ring detect time)
transient noise on the C.O. line from triggering a false ring.
ms
NOTE : Seconds shown as 'sec', milliseconds as 'ms', and minutes as 'mi'.
PROCEDURE
LCD DISPLAY
1. Press [TRSF/ALM] and dial 53
Display shows
2. Press [VOLUME (-) o r ( + ) ] to select a timer (e.g. CO SUPV)
3. Dial new time data(e.g. 0500)
4. Press [TRSF/ALM] to save and exit
DEFAULT DATA
CLEARING
: 00 SEC
CO SUPV
: 0000 MSEC
F DGT DLY
: 1000 MSEC
FLASH PBX
: 0600 MSEC
MFS ON TM
: 0100 MSEC
MF OFF TM
: 0100 MSEC
MPD DETCT
: 0060 MSEC
NEW CALL
: 2000 MS
NO RING
: 05 SEC
PAUSE TM
: 03 SEC
RNG DETCT
: 0200 MSEC
RELATED MMC
NONE
NX-SERIES
HYBRID KEY SYSTEM
PROGRAMMING SECTION
MMC 53
TRUNK WIDE TIMER
4Programmi ng 1999.9.15 12:43 PM 페이지52
