Falmec QUASAR 80 - Инструкция по эксплуатации - Страница 17

17

ENGLISH

 SAFETY INSTRUCTIONS
 AND WARNINGS

Installation operations are to be carried out 
by skilled and qualified installers in accor-

dance with the instructions in this booklet and in 
compliance with the regulations in force.
DO NOT use the hood if the power supply cable 
or other components are damaged:

disconnect the 

hood from the electrical power supply and contact the 
Dealer or an authorised Servicing Dealer for repairs. 

Do not modify the electrical, mechanical or func-
tional structure of the equipment.
Do not personally try to carry out repairs or repla-
cements. Interventions carried out by incompe-
tent and unauthorised persons can cause serious 
damage to the unit or physical and personal harm, 
not covered by the Manufacturer's warranty.

WARNINGS FOR THE INSTALLER

TECHNICAL SAFETY

Before installing the hood, check the in-
tegrity and function of each part. Should 
anomalies be noted, do not proceed with 

installation and contact the Dealer.

Do NOT install the hood if an aesthetic (or cos-
metic) defect has been detected. Put it back into 
its original package and contact the dealer.
No claim can be made for aesthetic (or cosmetic) 
defects once it has been installed.

During installation, always use personal protective 
equipment (e.g.: Safety shoes) and adopt prudent 
and proper conduct.
The installation kit (screws and plugs) supplied with 
the hood is only to be used on masonry walls: in case 
of installation on walls of a different material, assess 
other installation options keeping in mind the type 
of wall surface and the weight of the hood (indicated 
on page 2).
Keep in mind that installations with different types of 
fastening systems from those supplied, or which are 
not compliant, can cause electrical and mechanical 
seal danger.
Do not install the hood outdoors and do not expose 
it to atmospheric elements (rain, wind, etc.).

ELECTRICAL SAFETY

The electrical system to which the hood is 
to be connected must be in accordance 
with local standards and supplied with 

earthed connection in compliance with safety 
regulations in the country of use. It must also 
comply with European standards regarding radio 
antistatic properties. 

Before installing the hood, check that the electrical 
mains power supply corresponds with what is report-
ed on the identification plate located inside the hood.
The socket used to connect the installed equipment 
to the electrical power supply must be within reach: 
otherwise, install a mains switch to disconnect the 
hood when required.
Any changes to the electrical system must be carried 
out by a qualified electrician. 
The maximum length of the flue fastening screws 
(supplied by the manufacturer) must be 13 mm. Use 
of non-compliant screws with these instructions can 
lead to danger of an electrical nature.
Do not try to solve the problem yourself in the event 
of equipment malfunction, but contact the Dealer or 
an authorised Servicing Department for repairs.

When installing the hood, disconnect 
the equipment by removing the plug or 

switching off the main switch.

FUMES DISCHARGE SAFETY

Do no connect the equipment to discharge 
pipes of fumes produced from combustion 
(for example boilers, fireplaces, etc.).

Before installing the hood, ensure that all standards in 
force regarding discharge of air out of the room have 
been complied with.

USER WARNINGS

These warnings have been drawn up for 
your personal safety and those of others. 
You are therefore kindly asked to read the 

booklet carefully in its entirety before using the 
or cleaning the equipment.
The Manufacturer declines all responsibility for 
any damage caused directly, or indirectly, to per-
sons, things and pets as a consequence of failing 
to comply with the safety warnings indicated in 
this booklet.
It is imperative that this instructions booklet is 
kept together with the equipment for any future 
consultation.

If the equipment is sold or transferred to another person, 
make sure that the booklet is also supplied so that the 
new user can be made aware of the hood's operation 
and relative warnings. 

After the stainless steel hood has been installed, it will 
need to be cleaned to remove any residues remaining 
from the protection adhesive as well as any grease and 
oil stains which, if not removed, can cause irreversible 
damage to the hood surface. To properly clean the unit, 
the manufacturer recommends using the supplied 
moist wipes, which are also available sold separately. 

Insist on original spare parts.