Beurer DS 61 - Инструкция по эксплуатации - Страница 18

18

7 Display

  7.1  Kilocalories display

  7.2  Kilojoules display

  7.3  Displaying the carbohydrate content

  7.4  Displaying the cholesterol content

  7.5  Fat content display

  7.6  Displaying the code

  7.7  Weight display

  7.8  Displaying the number of memory spaces

  7.9  Protein content display

  7.10  Bread units display

8  Digital buttons 0 – 9 for entering the foodstuffs code

9  Battery compartment (back)

5. Initial use

Changing the weight unit

The scales can display values in the weight units 

g

 (grams) or 

oz

 (ounces). The default setting is in 

grams. You can adjust the unit using the 

unit

 button.

Positioning scales

Place the scales on a firm, even surface. A firm base 

is essential to correct measurement.

6. Usage

6.1 Weighing
Switching on scales

The display shows the weight of the item to be 

weighed. Press the   button.

Weighing additional items (tare)

To weigh additional quantities you can reset the 

scales to 0 g.

➔

 To do this, press 

tara

.

Entering the foodstuffs code

➔

  From the food list (page 21 onwards), find the 

3-digit code for the material you want to weigh 

and enter this number using the digit buttons.

If you have entered the wrong number, fill in the code 

with any numbers up to three digits. Then reenter the 

code again.
The display now shows all nutritional and energy values.
Please note that, due to natural fluctuations in the 

nutritional and energy values of foodstuffs only 

approximate data is possible.

Switching off scales

The scales switch off automatically 180 seconds 

after the last weighing change.

Press the   button to switch off manually.

6.2 Saving weighed items

You can save the weight, nutritional and energy val-

ues of the foodstuff currently being measured. The 

scales automatically add up the values of each meas-

urement stored. You can view the total weight, total 

nutritional values and total energy values at any time.

The saved data is retained even if the scales are 

switched on and off or if the battery is changed.

Saving the first measurement

You have previously done a measurement and 

entered the foodstuffs code.

➔

 Press the memory button 

M+

.

The display shows the summation symbol 

ΣM

, the 

memory space (e.g. 

01

) and the total weight.

Saving other measurements

Substitute the item to be weighed and repeat step 1.

Displaying added measured values

To retrieve the saved values, e.g. on a daily basis:

➔

 Press the memory button 

MR

.

The display shows the summation symbol 

ΣM

, the 

number of memory spaces (e.g. 

02

) and the total 

stored weight as well as the total nutritional and 

energy values.

Clear memory

Clear the memory regularly, e.g. on a daily basis.

➔

 Press the memory button 

MC

.

The symbol 

M

 clears. The memory has been cleared.

6.3 Programming your own food codes

The appliance has stored nutritional and energy val-

ues for 950 foods (memory locations 000 – 949). 

You can program a further 50 memory locations 

(950 – 999) with your own types of food and enter 

these in the blank lines of the table in the section on 

“Food codes”. To this purpose you have to know the 

nutritional and energy values of these foods.

 Note

The nutritional and energy values to be entered relate 

to a weight of 100 g of the specific type of food.

Please proceed as follows in order to program the 

additional types of food:

•  Turn the appliance on. In order to do this, press 

the button  .

•  Press the buttons 

tara

 and 

MR

 simultaneously 

for approximately three seconds. The appliance 

changes to the programming mode. The display 

for the food code shows the value 950. The last 

two figures flash.

•  Enter the desired food code (figures 50 – 99) and 

confirm the input by pressing the button 

MR

.

Then the energy value of the food is requested.