Ryobi RBC31SBO 5133002541 - Инструкция по эксплуатации - Страница 5

3

English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

USING THE REELEASY™ GRASS TRIMMER HEAD 
AND TRI-ARC™ BLADE

■

When using the ReelEasy™ grass trimmer head, the

grass deflector must be attached to the blade guard.
(

See page 2

03

). 

■

When using the Tri-Arc™ blade, the grass deflector

must be removed from the blade guard (

See page 2

02

)

. 

 WARNING

Always remove the pin for locking the gear shaft 
before starting the engine 

(see page 1

85

, step 4)

.

OPERATION

FUELING AND REFUELING

See page 1

84

.

■

Always handle fuel with care, it is highly flammable.

■

The product is powered by a 2-stroke engine and
requires pre-mixing petrol and 2-stroke lubricant.
Premix unleaded petrol and 2-stroke engine lubricant in 
a clean container approved for petrol.

■

This engine is certified to operate on unleaded petrol
intended for automotive use with an octane rating of 91 
([R + M] / 2) or higher.

■

Do not use any type of pre-mixed petrol / lubricant from 
fuel service stations.

■

Use synthetic 2-stroke lubricant only. Do not use
automotive lubricant or 2-stroke outboard lubricant.

■

Mix 2% synthetic 2-stroke lubricant into the petrol. This
is a 50:1 ratio.

■

Mix the fuel thoroughly and also each time before
fueling.

■

Mix in small quantities. Do not mix quantities larger than 
usable in a 30 day period. A synthetic 2-stroke lubricant 
containing a fuel stabilizer is recommended.

FILLING THE TANK

■

Clean surface around fuel cap to prevent contamination.

■

Loosen fuel cap slowly to release pressure and to keep 
fuel from escaping around the cap.

■

Carefully pour fuel mixture into the tank. Avoid spillage.

■

Prior to replacing the fuel cap, clean and inspect the
gasket.

■

Immediately replace fuel cap and hand tighten. Wipe
upany fuel spillage. Move 9 m away from refueling site
before starting engine.

STARTING THE ENGINE USING AN ELECTRICAL 
STARTER (OPTIONAL):

See page 

196

 to 2

01

.

 WARNING

Only use the Ryobi OES18 electrical starter. Use of any 
other starter may damage the engine and cause serious 
personal injury.

 WARNING

Before using the electrical starter to start the product, 
please read and understand completely the operation 
manual of the OES18 electrical starter to avoid improper 
operation and serious personal injury.

■

Hold the insulated shaft with your left hand and use
your right hand to put the starter bit shaft to the shaft
hole on the engine, otherwise the engine will not turn. 

■

Make sure the starter bit is properly engaged.

NOTE: 

The electrical starter is equipped with a safety 

interlock. Do not press and hold on the switch button when 
putting the electrical starter shaft into the shaft hole on the 
engine. Also, the starter will not turn if the electrical starter 
is not properly engaged.

OPERATING THE GRASS TRIMMER

See page 1

89

.

RBC31SESO:

 Hold the product with the right hand on the 

rear handle and the left hand on the front handle.

RBC31SBO: 

Hold the product with the right hand on the 

trigger handle and the left hand on the left handle.

■

Keep a firm grip with both hands while in operation.

■

The product should be held at a comfortable position
with the trigger handle about hip height.

■

Always operate the product at full throttle. Prolonged
cutting at partial throttle will result in lubricant dripping
from the silencer.

■

Cut tall grass from the top down to prevent grass from
wrapping around the shaft housing and string head,
which may cause damage from overheating.

■

If grass or debris becomes wrapped around the cutting
means, stop the engine. Wear heavy-duty gloves
to prevent injury from the sharp blades and carefully
remove the debris.

■

Do not push into the grass to be cut. Move from side
to side. Move forward a little at the end of each sweep.

■

Keep the product tilted towards the area being cut.

■

Do not use in dangerous environments.

■

Use the tip of the string to do the cutting; do not force
the string head into the uncut grass.

■

Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, kerbs and wood may
wear string rapidly.

■

Avoid trees and shrubs. Tree bark, wood mouldings,
cladding and fence posts can be easily damaged by
the string.

OPERATING THE BRUSHCUTTER

See page 1

92

.

To help reduce the risk of kickback: Do not push into the 
material to be cut. Move from right to left in steady sweeps. 
Move forward a little at the beginning of each new sweep.

RBC31SESO: 

Hold the product with the right hand on the 

rear handle and the left hand on the front handle.

RBC31SBO: 

Hold the product with the right hand on the 

trigger handle and the left hand on the left handle.