Ryobi OLT1825 5133001808 - Инструкция по эксплуатации - Страница 4

English

2

BATTERY TOOL USE AND CARE

Ŷ

Recharge only with the charger specified by the 

manufacturer.

 A charger that is suitable for one type 

of battery pack may create a risk of fire when used with 

another battery pack.

Ŷ

Use power tools only with specifically designated 

battery packs.

 Use of any other battery packs may 

create a risk of injury and fire.

Ŷ

When battery pack is not in use, keep it away from 

other metal objects like, paper clips, coins, keys, 

nails, screws, or other small metal objects, that can 

make a connection from one terminal to another.

Shorting the battery terminals together may cause 

burns or a fire.

Ŷ

Under abusive conditions, liquid may be ejected 

from the battery; avoid contact. If contact 

accidentally occurs, flush with water. If liquid 

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or 

burns.

SERVICE

Ŷ

Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

This will ensure that the safety of the power tool is 

maintained.

SPECIFIC SAFETY RULES

 WARNING

When using the product, the safety rules must be 

followed. For your own safety and that of bystanders, 

please read these instructions before operating the 

product. Please keep the instructions safe for later use.

 WARNING

This appliance is not intended for use by persons 

(including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, 

unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible 

for their safety. Children should be supervised to ensure 

that they do not play with the appliance.

Ŷ

Stop machine if anyone enters the area. Never operate 

the machine while people, especially children, or 

pets are nearby. If you are approached, stop the unit 

immediately.

Ŷ

Avoid using machine in bad weather, especially if there 

is risk of lightning.

Ŷ

Use the product in daylight or good artificial light.

Ŷ

Avoid using on wet grass.

Ŷ

Keep proper footing and balance at all times.

Ŷ

Do not walk backwards when trimming.

Ŷ

Walk, never run.

Ŷ

Keep the trimmer head below waist level.

Ŷ

Do not cut on surfaces other than grass on ground.

Ŷ

Never operate the product with damaged guards or 

without guards in place.

Ŷ

Never fit a metal replacement line.

Ŷ

Keep hands and feet away from the cutting means at 

all times and especially when switching on the motor.

Ŷ

Thoroughly inspect the area where the machine is to be 

used and remove all rocks, sticks, metal, wire, bones, 

toys, or other foreign objects.

Ŷ

Switch off and disconnect from the power supply before:

–

servicing

–

leaving the trimmer unattended

–

cleaning your trimmer

–

changing accessories

–

checking for any damage after hitting an object

–

checking for any damage if the trimmer starts to 

vibrate abnormally

–

performing maintenance

Ŷ

Wear protective glasses or goggles.

Ŷ

Take care against injury from any device fitted for 

trimming the filament line length.

MAINTENANCE

Ŷ

Use only genuine replacement parts and accessories.

Ŷ

After extending new cutter line, always return the 

product to its normal operating position before switching 

on.

Ŷ

After each use, clean with a soft dry cloth.

Ŷ

Check all nuts, bolts and screws at frequent intervals 

for proper tightness to ensure the product is in safe 

working condition. Any part that is damaged should be 

properly repaired or replaced by an authorized service 

centre.

Ŷ

When not in use, the product should be stored in a cool 

dry place and locked up out of the reach of children. Do 

not store outdoors.

Inspection after dropping or other impacts

Thoroughly inspect the product and identify any affections 

or damage with it. Any part that is damaged should be 

properly repaired or replaced by an authorized service 

centre.

RESIDUAL RISKS

It has been reported that vibrations from hand-held tools 

may contribute to a condition called Raynaud’s Syndrome 

in certain individuals. Symptoms may include tingling, 

numbness and blanching of the fingers, usually apparent 

upon exposure to cold. 
Hereditary factors, exposure to cold and dampness, diet, 

smoking and work practices are all thought to contribute to 

the development of these symptoms. There are measures 

that can be taken by the operator to possibly reduce the 

effects of vibration:

Ŷ

Keep your body warm in cold weather. When operating 

the unit wear gloves to keep the hands and wrists 

warm. It is reported that cold weather is a major factor 

contributing to Raynaud’s Syndrome.