Makita G-серия HP488DWE - Инструкция по эксплуатации - Страница 7

7 ENGLISH

3. 

Always be sure you have a firm footing. Be 

sure no one is below when using the tool in 

high locations.

4. 

Hold the tool firmly.

5. 

Keep hands away from rotating parts.

6. 

Do not leave the tool running. Operate the tool 

only when hand-held.

7. 

Do not touch the drill bit, the workpiece or 

chips immediately after operation; they may be 

extremely hot and could burn your skin.

8. 

Some material contains chemicals which may 

be toxic. Take caution to prevent dust inhala

-

tion and skin contact. Follow material supplier 

safety data.

9. 

If the drill bit cannot be loosened even you 

open the jaws, use pliers to pull it out.

 In such a 

case, pulling out the drill bit by hand may result in 

injury by its sharp edge.

10. 

Make sure there are no electrical cables, water 

pipes, gas pipes etc. that could cause a hazard 

if damaged by use of the tool.

Safety instructions when using long drill bits

1. 

Never operate at higher speed than the max

-

imum speed rating of the drill bit.

 At higher 

speeds, the bit is likely to bend if allowed to rotate 

freely without contacting the workpiece, resulting 

in personal injury.

2. 

Always start drilling at low speed and with the 

bit tip in contact with the workpiece.

 At higher 

speeds, the bit is likely to bend if allowed to rotate 

freely without contacting the workpiece, resulting 

in personal injury.

3. 

Apply pressure only in direct line with the bit 

and do not apply excessive pressure.

 Bits can 

bend causing breakage or loss of control, resulting 

in personal injury.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc

-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using 

battery.

2. 

Do not disassemble or tamper with the battery 

cartridge.

 It may result in a fire, excessive heat, 

or explosion.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them 

out with clear water and seek medical atten

-

tion right away. It may result in loss of your 

eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con

-

ductive material.

(2) 

Avoid storing battery cartridge in a con

-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store and use the tool and battery car

-

tridge in locations where the temperature may 

reach or exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Do not nail, cut, crush, throw, drop the battery 

cartridge, or hit against a hard object to the 

battery cartridge.

 Such conduct may result in a 

fire, excessive heat, or explosion.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 

to the Dangerous Goods Legislation require

-

ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult

-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

When disposing the battery cartridge, remove 

it from the tool and dispose of it in a safe 

place. Follow your local regulations relating to 

disposal of battery.

12. 

Use the batteries only with the products 

specified by Makita.

 Installing the batteries to 

non-compliant products may result in a fire, exces

-

sive heat, explosion, or leak of electrolyte.

13. 

If the tool is not used for a long period of time, 

the battery must be removed from the tool.

14. 

During and after use, the battery cartridge may 

take on heat which can cause burns or low 

temperature burns. Pay attention to the han

-

dling of hot battery cartridges.

15. 

Do not touch the terminal of the tool imme

-

diately after use as it may get hot enough to 

cause burns.

16. 

Do not allow chips, dust, or soil stuck into the 

terminals, holes, and grooves of the battery 

cartridge.

 It may result in poor performance or 

breakdown of the tool or battery cartridge.

17. 

Unless the tool supports the use near 

high-voltage electrical power lines, do not use 

the battery cartridge near high-voltage electri-

cal power lines.

 It may result in a malfunction or 

breakdown of the tool or battery cartridge.

18. 

Keep the battery away from children.

SAVE THESE INSTRUCTIONS.