Bosch GDR 10,8-LI 0.601.9A6.972 - Инструкция по эксплуатации - Страница 18

18

 | English 

2 609 140 699 | (3.12.09)

Bosch Power Tools

Noise/Vibration Information

Measured sound values determined according 
to EN 60745.
Typically the A-weighted noise levels of the 
product are: Sound pressure level 87 dB(A); 
Sound power level 98 dB(A). Uncertainty 
K = 3 dB.

Wear hearing protection!

Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Impact tightening of fasteners of the maximum 
capacity of the tool: Vibration emission value 
a

h

= 9 m/s

2

, Uncertainty K = 1.5 m/s

2

.

The vibration emission level given in this infor-
mation sheet has been measured in accordance 
with a standardised test given in EN 60745 and 
may be used to compare one tool with another. 
It may be used for a preliminary assessment of 
exposure.
The declared vibration emission level repre-
sents the main applications of the tool. However 
if the tool is used for different applications, with 
different accessories or poorly maintained, the 
vibration emission may differ. This may signifi-
cantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibra-
tion should also take into account the times 
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect 
the operator from the effects of vibration such 
as: maintain the tool and the accessories, keep 
the hands warm, organisation of work patterns. 

Declaration of Conformity

We declare under our sole responsibility that 
the product described under “Technical Data” is 
in conformity with the following standards or 
standardization documents: EN 60745 accord-
ing to the provisions of the directives 
2004/108/EC, 98/37/EC (until 28 Dec 2009), 
2006/42/EC (from 29 Dec 2009).

Technical file at:
Robert Bosch GmbH, PT/ESC, 
D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

26.10.2009

Assembly

Battery Charging (see figure A)

f

Use only the battery chargers listed on the 
accessories page. 

Only these battery charg-

ers are matched to the lithium ion battery of 
your power tool.

Note: 

The battery is supplied partially charged. 

To ensure full capacity of the battery, complete-
ly charge the battery in the battery charger be-
fore using your power tool for the first time.
The lithium ion battery can be charged at any 
time without reducing its service life. Interrupt-
ing the charging procedure does not damage the 
battery.
The lithium ion battery is protected against 
deep discharging by the “Electronic Cell Protec-
tion (ECP)”. When the battery is empty, the ma-
chine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.

Do not continue to press the 
On/Off switch after the ma-

chine has been automatically switched off. 

The 

battery can be damaged.
To remove the battery 

7

 press the unlocking but-

tons 

6

 and pull out the battery downwards. 

Do 

not exert any force.

The battery is equipped with a NTC temperature 
control which allows charging only within a tem-
perature range of between 0 ° C and 45 ° C. A 
long battery service life is achieved in this man-
ner.
Observe the notes for disposal.

Dr. Egbert Schneider
Senior Vice President
Engineering

Dr. Eckerhard Strötgen
Head of Product
Certification

WARNING

OBJ_BUCH-1066-001.book  Page 18  Thursday, December 3, 2009  9:10 AM