Einhell TE-SM 2131 - Инструкция по эксплуатации - Страница 29

GB

- 29 -

• 

Important! Every time that you change the 

saw blade, check to see that it spins freely in 

the table insert (12) in both perpendicular and 

45° angle settings.

• 

Important! The work to change and align the 

saw blade (7) must be carried out correctly.

6.8 Transport (Fig. 1-3)

• 

Retighten the locking screw (14) to secure the 

turntable (17) in place.

• 

Activate the release button (3), press the ma-

chine head (4) downwards and secure with 

the safety pin (25). The saw is now locked in 

its bottom position.

• 

Fix the saw‘s drag function with the locking 

screw for drag guide (24) in rear position.

• 

Carry the equipment by the fixed saw table 

(18) and the transport handle. 

• 

To set up the equipment again, proceed as 

described in section 5.2.

6.9 Operating the laser (Fig. 3)

To switch on:

 Move the On/O

ff

  switch (36) to the 

“I” position to switch on the laser (30). A laser line 

is projected onto the material you wish to pro-

cess, providing an exact guide for the cut.

To switch o

ff

 : 

Move the On/O

ff

  switch (36) to the 

“0” position.

6.10 Operating the LED lamp (Fig. 2)

• 

For good illumination of the work area you 

can use the LED lamp in addition to the room 

lighting.

• 

To switch on: Switch position „I“

• 

To switch off: Switch position „0“

• 

If the machine is equipped with an LED, this 

LED is not allowed to be replaced by a diffe-

rent type of LED. Repairs are allowed to be 

carried out only by the manufacturer of the 

LED or one of his authorized agents.

6.11 Electric brake

For safety reasons, the equipment is supplied 

with an electric brake system for the saw blade. 

The equipment may therefore emit an odor or 

generate sparks when it is switched o

ff

 . This has 

no in

fl

 uence on the operational performance or 

safety of the equipment.

7.  Replacing the power cable

Danger!

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

8.  Cleaning, maintenance and 

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon  

brushes checked only by a quali

fi

 ed electrician.

Danger!

 The carbon brushes should not be rep 

laced by anyone but a quali

fi

 ed electrician.

8.3 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

8.4 Ordering replacement parts:

Please quote the following data when ordering 

replacement parts:

• 

 Type of machine

• 

 Article number of the machine

• 

 Identification number of the machine

• 

 Replacement part number of the part required

For our latest prices and information please go to 

www.isc-gmbh.info

Anl_TE_SM_2131_Dual_SPK7.indb   29

Anl_TE_SM_2131_Dual_SPK7.indb   29

13.05.14   16:04

13.05.14   16:04