Makita DHS900Z - Инструкция по эксплуатации - Страница 25

ENGLISH

State of abnormality

Probable cause (malfunction)

Remedy

The vacuum cleaner does not run 

along with the switch operation of 

the tool.

The wireless unit is not installed into 

the tool. 

The wireless unit is improperly installed 

into the tool.

Install the wireless unit correctly.

The terminal of the wireless unit and/or 

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the 

wireless unit and clean the slot.

The wireless activation button on the 

tool has not been pushed.

Push the wireless activation button briefly and make 

sure that the wireless activation lamp is blinking 

in blue.

The stand-by switch on the vacuum 

cleaner is not set to "AUTO".

Set the stand-by switch on the vacuum cleaner to 

"AUTO".

More than 10 tools are registered to the 

vacuum cleaner.

Perform the tool registration again. 

If more than 10 tools are registered to the vacuum 

cleaner, the tool registered earliest will be cancelled 

automatically.

The vacuum cleaner erased all tool 

registrations.

Perform the tool registration again.

No power supply

Supply the power to the tool and the vacuum 

cleaner.

The tool and vacuum cleaner are away 

from each other (out of the transmission 

range).

Get the tool and vacuum cleaner closer each other. 

The maximum transmission distance is approxi-

mately 10 m however it may vary according to the 

circumstances.

Radio disturbance by other appliances 

which generate high-intensity radio 

waves.

Keep the tool and vacuum cleaner away from the 

appliances such as Wi-Fi devices and microwave 

ovens.

The vacuum cleaner runs while the 

tool's switch trigger is not pulled.

Other users are using the wireless 

activation of the vacuum cleaner with 

their tools.

Turn off the wireless activation button of the other 

tools or cancel the tool registration of the other 

tools.

MAINTENANCE

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before attempting to perform inspection or 

maintenance.

CAUTION:

Clean out the upper and lower 

guards to ensure there is no accumulated saw-

dust which may impede the operation of the lower 

guarding system.

 A dirty guarding system may limit 

the proper operation which could result in serious 

personal injury. The most effective way to accomplish 

this cleaning is with compressed air. 

If the dust is 

being blown out of the guards, be sure the proper 

eye and breathing protection is used.

CAUTION:

After each use, wipe off the saw 

dust on the tool.

 Fine saw dust may come inside the 

tool and cause malfunction or a fire.

NOTICE:

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

Adjusting 0°-cut or 45°-cut accuracy

NOTICE:

Do not engage the levers for -1° bevel 

angle when adjusting 0°-cut accuracy.

NOTICE:

Do not engage the positive stopper for 

22.5° or 60° bevel angle when adjusting 45°-cut 

accuracy.

This adjustment has been made at the factory. But if it is 

off, you can adjust it as the following procedure.

1.

  Loosen the clamping screws on the front and rear 

of the tool so that the bevel angle can be changed. Set 

the positive stopper to 45° bevel angle position if you 

are going to adjust 45°-cut accuracy.

► 

Fig.48:

1.

 Clamping screw 

2.

 Positive stopper

2.

  Make the base perpendicular or 45° to the circular 

saw blade using a triangular rule by turning the adjust

-

ing screw with a hex wrench. You can also use a square 

rule to adjust 0° angle.

► 

Fig.49:

1.

 Triangular rule

► 

Fig.50:

1.

 Adjusting screw for 0° angle 

2.

 Adjusting 

screw for 45° angle

3.

  Tighten the clamping screws and then make a test 

cut to check if desired angle is obtained.

25