Makita DHS900Z - Инструкция по эксплуатации - Страница 21

ENGLISH

Hold the tool firmly. The tool is provided with both a front 

grip and rear handle. Use both to best grasp the tool. 

If both hands are holding saw, they cannot be cut by 

the circular saw blade. Set the base on the workpiece 

to be cut without the circular saw blade making any 

contact. Then turn the tool on and wait until the circular 

saw blade attains full speed. Now simply move the tool 

forward over the workpiece surface, keeping it flat and 

advancing smoothly until the sawing is completed.

To get clean cuts, keep your sawing line straight and 

your speed of advance uniform. If the cut fails to prop

-

erly follow your intended cut line, do not attempt to turn 

or force the tool back to the cut line. Doing so may bind 

the circular saw blade and lead to dangerous kickback 

and possible serious injury. Release switch, wait for cir

-

cular saw blade to stop and then withdraw tool. Realign 

tool on new cut line, and start cut again. Attempt to 

avoid positioning which exposes operator to chips and 

wood dust being ejected from saw. Use eye protection 

to help avoid injury.

NOTE:

 When making a miter cuts etc., sometimes 

the lower guard does not move easily. At that time, 

use the retracting lever to raise the lower guard for 

starting cut and as soon as blade enters the material, 

release the retracting lever.

► 

Fig.30:

1.

 Retracting lever

Sub base (Guide rule)

CAUTION:

Make sure that the sub base (guide 

rule) is securely installed in the correct position 

before use.

 Improper attachment may cause danger

-

ous kickback.

By using the sub base as a guide rule, you can perform 

extra-accurate straight cuts. Loosen the clamping 

screws and slide the sub base out from the tool then 

insert it upside down.

► 

Fig.31:

1.

 Clamping screw 

2.

 Sub base

Simply slide the fence of the sub base snugly against 

the side of the workpiece and secure it in position with 

the clamping screws. It also makes repeated cuts of 

uniform width possible.

► 

Fig.32:

1.

 Clamping screw 

2.

 Sub base

Guide rail

Optional accessory

NOTICE:

 Remove the sub base when using the 

guide rail.

Place the tool on the rear end of guide rail. Turn two adjust

-

ing screws on the tool base so that the tool slides smoothly 

without a clatter. Hold both the front grip and rear handle of 

the tool firmly. Turn on the tool and cut the splinter-guard 

along the full length with a stroke. Now the edge of the splin-

ter-guard corresponds to the cutting edge.

► 

Fig.33:

1.

 Adjusting screws

When bevel cutting with the guide rail, use the slide 

lever to prevent the tool from falling over.

Move the slide lever on the tool base in the direction 

of arrow so that it engages the undercut groove in the 

guide rail.

► 

Fig.34:

1.

 Slide lever

Lanyard (tether strap) connection

Safety warnings specific for use at height

Read all safety warnings and instructions.

 Failure 

to follow the warnings and instructions may result in 

serious injury.

1. 

Always keep the tool tethered when working 

"at height". Maximum lanyard length is 2 m 

(6.5 ft).

The maximum permissible fall height for lan-

yard (tether strap) must not exceed 2 m (6.5 ft).

2. 

Use only with lanyards appropriate for this tool 

type and rated for at least 7.0 kg (15.4 lbs).

3. 

Do not anchor the tool lanyard to anything on 

your body or on movable components. Anchor 

the tool lanyard to a rigid structure that can 

withstand the forces of a dropped tool.

4. 

Make sure the lanyard is properly secured at 

each end prior to use.

5. 

Inspect the tool and lanyard before each use 

for damage and proper function (including 

fabric and stitching). Do not use if damaged or 

not functioning properly.

6. 

Do not wrap lanyards around or allow them to 

come in contact with sharp or rough edges.

7. 

Fasten the other end of the lanyard outside 

the working area so that a falling tool is held 

securely.

8. 

Attach the lanyard so that the tool will move 

away from the operator if it falls.

 Dropped tools 

will swing on the lanyard, which could cause injury 

or loss of balance.

9. 

Do not use near moving parts or running 

machinery.

 Failure to do so may result in a crush 

or entanglement hazard.

10. 

Do not carry the tool by the attachment device 

or the lanyard.

11. 

Only transfer the tool between your hands 

while you are properly balanced.

12. 

Do not attach lanyards to the tool in a way that 

keeps guards, switches or lock-offs from oper

-

ating properly.

13. 

Avoid getting tangled in the lanyard.

14. 

Keep lanyard away from the cutting area of the 

tool.

15. 

Use multi-action and screw gate type cara-

bineers. Do not use single action spring clip 

carabineers.

16. 

In the event the tool is dropped, it must be 

tagged and removed from service, and should 

be inspected by a Makita Factory or Authorized 

Service Center.

► 

Fig.35:

1.

 Hole for lanyard (tether strap)

21