Makita DHS782ZJ - Инструкция по эксплуатации - Страница 11

11 ENGLISH

NOTE:

 The declared vibration total value(s) has been 

measured in accordance with a standard test method 

and may be used for comparing one tool with another.

NOTE:

 The declared vibration total value(s) may also 

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during 

actual use of the power tool can differ from the 

declared value(s) depending on the ways in which 

the tool is used especially what kind of workpiece 

is processed.

WARNING:

Be sure to identify safety mea-

sures to protect the operator that are based on an 

estimation of exposure in the actual conditions of 

use (taking account of all parts of the operating 

cycle such as the times when the tool is switched 

off and when it is running idle in addition to the 

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A 

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specifications provided 

with this power tool.

 Failure to follow all instructions 

listed below may result in electric shock, fire and/or 

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your 

mains-operated (corded) power tool or battery-operated 

(cordless) power tool.

Cordless circular saw safety warnings

Cutting procedures

1. 

DANGER: Keep hands away from cutting 

area and the blade. Keep your second hand 

on auxiliary handle, or motor housing.

 If both 

hands are holding the saw, they cannot be cut by 

the blade.

2. 

Do not reach underneath the workpiece.

 The 

guard cannot protect you from the blade below the 

workpiece.

3. 

Adjust the cutting depth to the thickness of 

the workpiece.

 Less than a full tooth of the blade 

teeth should be visible below the workpiece.

4. 

Never hold the workpiece in your hands or 

across your leg while cutting. Secure the 

workpiece to a stable platform.

 It is important to 

support the work properly to minimise body expo

-

sure, blade binding, or loss of control.

► 

Fig.1

5. 

Hold the power tool by insulated gripping surfaces, 

when performing an operation where the cutting 

tool may contact hidden wiring.

 Contact with a “live” 

wire will also make exposed metal parts of the power 

tool “live” and could give the operator an electric shock.

6. 

When ripping, always use a rip fence or 

straight edge guide.

 This improves the accuracy 

of cut and reduces the chance of blade binding.

7. 

Always use blades with correct size and shape 

(diamond versus round) of arbour holes.

 Blades 

that do not match the mounting hardware of the 

saw will run off-centre, causing loss of control.

8. 

Never use damaged or incorrect blade wash-

ers or bolt.

 The blade washers and bolt were 

specially designed for your saw, for optimum 

performance and safety of operation.

Kickback causes and related warnings

— 

kickback is a sudden reaction to a pinched, jammed or 

misaligned saw blade, causing an uncontrolled saw to 

lift up and out of the workpiece toward the operator;

— 

when the blade is pinched or jammed tightly by the 

kerf closing down, the blade stalls and the motor reac-

tion drives the unit rapidly back toward the operator;

—  if the blade becomes twisted or misaligned in the cut, 

the teeth at the back edge of the blade can dig into 

the top surface of the wood causing the blade to climb 

out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect 

operating procedures or conditions and can be avoided 

by taking proper precautions as given below.

1. 

Maintain a firm grip with both hands on the saw 

and position your arms to resist kickback forces. 

Position your body to either side of the blade, but 

not in line with the blade.

 Kickback could cause the 

saw to jump backwards, but kickback forces can be con

-

trolled by the operator, if proper precautions are taken.

2. 

When blade is binding, or when interrupting a 

cut for any reason, release the trigger and hold 

the saw motionless in the material until the 

blade comes to a complete stop. Never attempt 

to remove the saw from the work or pull the 

saw backward while the blade is in motion or 

kickback may occur.

 Investigate and take correc-

tive actions to eliminate the cause of blade binding.

3. 

When restarting a saw in the workpiece, centre 

the saw blade in the kerf so that the saw teeth 

are not engaged into the material.

 If a saw blade 

binds, it may walk up or kickback from the work

-

piece as the saw is restarted.

4. 

Support large panels to minimise the risk of 

blade pinching and kickback.

 Large panels tend 

to sag under their own weight. Supports must be 

placed under the panel on both sides, near the line 

of cut and near the edge of the panel.

► 

Fig.2

► 

Fig.3

5. 

Do not use dull or damaged blades.

 Unsharpened 

or improperly set blades produce narrow kerf caus

-

ing excessive friction, blade binding and kickback.

6. 

Blade depth and bevel adjusting locking levers 

must be tight and secure before making the 

cut.

 If blade adjustment shifts while cutting, it may 

cause binding and kickback.