Monster iSport Freedom Wireless Bluetooth Black - Инструкция по эксплуатации - Страница 3

Physiology of the Ear and Hearing

For additional information on what loud noises do to your ear and chart reference www.
abelard.org/hear/hear.php#loud-music

Use Responsibly

Do not use headphones when it’s unsafe to do so—while operating  

a vehicle, riding a bike, crossing streets, or during any activity or  

in an environment where your full attention to your surroundings 

is required. 

It‘s dangerous to drive while wearing headphones, and in many 

places, illegal because it decreases your chances of hearing life-

saving sounds outside of your vehicle, such as another car’s horn  

and emergency vehicle sirens. 

Please avoid wearing your headphones while driving. Use one  

of Monster’s FM transmitters to listen to your mobile media  

devices instead. 

Cleaning

Wipe earcups with a soft cloth dampened with a mild soap solution. 

Keys and Parts

The headset contains the following parts:

Incus

Cochlear Nerve

Stapes

Tympanic

Membrane

Auditory Canal

Cochlea

Malleus

Vestibule

To Nose/Throat

1

5

2

6

3

7

4

8

9

10

1.  Multifunction key 

(Power On/Off, Pairing, 

Activate Voice Dialing) 

2.  Track back

3.  Volume down

4.  Indicator light 

(Only visible when lit)

5.  Play / Pause key  

(Answer/End/Reject Call)

6.  Track forward

7.  Volume up

8.  Charger connect

9.  3.5mm cable port

10.  Microphone

Before using the headset, you must charge the battery and pair the 

headset with a compatible device. Freedom will function without a 

charged battery when attached by cable to phone or music player. 

Charge the Battery

The headphone includes a Micro USB cable that can be connected 

to your computer or other device made for USB charging. Plug the 

Micro USB end of the included USB cable into the USB micro port 

charger connector under the left earcup of the headphone. Plug the 

other end into a USB port on your computer or other devices made 

for USB charging. The indicator light will be red while charging. Once 

fully charged, the green LED will be on. Charge time is 1.5 hours 

on an empty battery. The fully charged battery has power for up to 

10 hours talking and/or music time and up to 100 hours standby time.

WARNING: (1) Please pay attention to the environmental aspects of 

battery disposal. Battery must be recycled or disposed of properly. 

This product must not be disposed together with the domestic 

waste. This product has to be disposed at an authorized place for 

recycling of electrical and electronic appliances. By collecting and 

recycling waste, you help save natural resources, and make sure the 

product is disposed in an environmental friendly and healthy way. (2) 

Batteries (battery pack or batteries installed) should not be exposed 

to excessive heat, such as sunshine, fire, or the like. (3) DO NOT 

disassemble or replace the battery. If you suspect there is something 

wrong with the battery, please carry the unit to the service center 

for help.

Switch On

To switch on, press and hold the multifunction key about two 

seconds. The headset beeps ascending tones, and the green 

indicator light is briefly displayed. When the headset tries to 

connect to the last used phone or music player, the red indicator 

light flashes slowly. When the headset is connected to a device 

and is ready for use, the blue indicator light flashes slowly. If the 

headset has not been paired with a device, it automatically enters 

the pairing mode.

Switch Off

To switch off, press and hold the multifunction key for about three 

seconds. The headset beeps descending tones, and the red light is 

briefly displayed. If the headset is not connected to a device within 

10 minutes, it switches off automatically.

Pairing

1.  Ensure that your phone or music player is switched on.

2.  To pair the headset if it has not been previously paired with a 

device, switch on the headset. The headset enters the pairing 

mode, and the blue and red indicator light starts to flash quickly. 

To pair the headset if it has been previously paired with another 

device, ensure that the headset is switched off, and press and 

hold the multifunction key (for about five seconds) until the blue 

and red indicator light starts to flash quickly.

3.  Activate the 

Bluetooth

®

 feature on your phone or music player, 

and set it to search for 

Bluetooth

 devices.

4.  Select “Freedom” from the list of found devices on your phone 

or music player.

5.  If necessary, enter passcode 0000 to pair and connect the 

headset to your device.

Adjust the Volume

To adjust the headset volume, press the volume up or down key 

during a call or while listening to music. To adjust the volume 

quickly, press and hold either key.

WARNING: Excessive sound pressure from earphones and 

headphones can cause hearing loss. 

Calls

To make a call, use your mobile phone in the normal way when the 

headset is connected to it.