Bosch GST 10,8 V-Li - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

1 619 P11 351 | (1.10.13)

Technical Data

Noise/Vibration Information

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.

An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardisation documents: EN 60745 
according to the provisions of the directives 2009/125/EC 
(Regulation 1194/2012), 2011/65/EU, 2004/108/EC, 
2006/42/EC.

Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division 
D-70745 Leinfelden-Echterdingen 
Leinfelden, 23.08.2013

Assembly



Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport 

and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.

Battery Charging



Use only the battery chargers listed on the accessories 

page. 

Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: 

The battery is supplied partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.

The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.

The lithium ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.

Observe the notes for disposal.

Cordless Jigsaw

GST 10,8 V-LI

Article number

3 601 EA1 0..

Rated voltage

V=

10.8

Stroke rate at no load n

0

min

-1

1 500 – 2 800

Stroke

mm

18

Cutting capacity, max.
– in wood
– in  aluminium
– in non-alloy steel

mm
mm
mm

70

3
3

Bevel cuts (left/right), max.

°

45

Weight according to 
EPTA-Procedure 01/2003

kg

1.5 *

* dependent of the battery pack being used

Battery

Permitted ambient 
temperature
– when charging
– during operation*
– during  storage

° C
° C
° C

0 ... + 45

– 20 ... + 50
– 20 ... + 60

Recommended batteries

GBA 10,8 V x,x Ah O– .

* Limited performance at temperatures < 0 ° C

GST 10,8 V-LI

Measured sound values determined accord-
ing to EN 60745.

Typically the A-weighted noise levels of the 
product are
Sound pressure level
Sound power level
Uncertainty K

Wear hearing protection!

dB(A)
dB(A)

dB

77
88

3

Vibration total values a

h

 (triax vector sum) 

and uncertainty K determined according to 
EN 60745:Cutting board:
a

h

K
Cutting sheet metal:
a

h

K

m/s

2

m/s

2

m/s

2

m/s

2

5.5
1.5

5.0
1.5

Henk Becker
Executive Vice President
Engineering

Helmut Heinzelmann
Head of Product Certification
PT/ETM9

OBJ_BUCH-1994-001.book  Page 15  Tuesday, October 1, 2013  2:18 PM