Bosch 0.601.5A6.100 - Инструкция по эксплуатации - Страница 18

18

 | English 

1 609 92A 33H | (9.9.16)

Bosch Power Tools

After longer periods of work at low stroke rate, the machine 
can heat up considerably. Remove the saw blade from the 
machine and allow the machine to cool down by running it for 
approx. 3 minutes at maximum stroke rate.

GST 18 V-LI B: 

Increasing or reducing the pressure on the 

On/Off switch 

2

 enables stepless stroke-rate control of the 

switched-on machine.

Light pressure on the On/Off switch 

2

 results in a low stroke 

rate. Increasing the pressure also increases the stroke rate.

GST 18 V-LI S: 

With the thumbwheel for stroke rate preselec-

tion 

16

, the stroke rate can be preset and changed during 

operation.

Temperature Dependent Overload Protection

In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the 
permitted battery temperature range, the speed is reduced or 
the power tool switches off. At reduced speed, the power tool 
will run again at full speed once the permitted battery temper-
ature is reached or the load is reduced. During automatic 
shut-down, switch off the power tool, allow the battery to cool 
down, then switch the power tool back on.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.

Working Advice



When sawing small or thin workpieces, always use a 
firm support.

Contact Protector

The contact protector 

13

 attached to the casing prevents ac-

cidental touching of the saw blade during the working proce-
dure and may not be removed.

Plunge Cutting (see figure I)



Plunge cuts may only be applied to soft materials, such 
as wood, gypsum plaster boards, etc.!

Use only short saw blades for plunge cutting. Plunge cutting is 
possible only with the mitre angle set at 0 °.

Place the machine with the front edge of the base plate 

7

 on 

to the workpiece without the saw blade 

10

 touching the work-

piece and switch on. For machines with stroke rate control, 
select the maximum stroke rate. Firmly hold the machine 
against the workpiece and by tilting the machine, slowly 
plunge the saw blade into the workpiece.

When the base plate 

7

 fully lays on the workpiece, continue 

sawing along the desired cutting line.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be applied 
alongside cutting line because of the material heating up.

Maintenance and Service

Maintenance and Cleaning



For safe and proper working, always keep the machine 
and ventilation slots clean.

Clean the saw blade holder regularly. For this, remove the saw 
blade from the machine and lightly tap out the machine on a 
level surface.

Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of 
dust from below or overhead.

Lubricate the guide roller 

9

 occasionally with a drop of oil.

Check the guide roller 

9

 regularly. If worn, it must be replaced 

through an authorised Bosch after-sales service agent.

The plastic guide plate 

6

 should be replaced when worn.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

In all correspondence and spare parts orders, please always 
include the 10-digit article number given on the nameplate of 
the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045

OBJ_BUCH-2148-004.book  Page 18  Friday, September 9, 2016  9:14 AM