Bosch PFS 3000-2 - Инструкция по эксплуатации - Страница 18

18

 | English 

1 609 92A 3ZD | (13.9.17)

Bosch Power Tools



Do not use the power tool if the switch does not turn it 
on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.



Disconnect the plug from the power source and/or the 
battery pack from the power tool before making any 
adjustments, changing accessories, or storing power 
tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other 
condition that may affect the power tool’s operation. If 
damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 
tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account 
the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Service



Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Fine-spray Systems



Keep area clean, well lit and free of paint or solvent 
containers, rags, and other flammable materials.  

Spontaneous combustion may occur. Fire extinguisher 
equipment shall be present and working at all times.



Provide for good ventilation in the spraying area and 
for sufficient fresh air in the complete room. 

Evaporat-

ing inflammable solvents create an explosive environment.



Do not spray and clean with materials that have a flash 
point of less than 55 °C. Use materials based on water, 
non-volatile hydrocarbons or similar materials. 

Volatile 

evaporating solvents create an explosive environment.



Do not spray in the vicinity of ignition sources, such as 
static electricity sparks, open flames, pilot lights, hot 
objects, engines/motors, cigarettes and sparks from 
plugging in or unplugging power cords or operating 
switches. 

Such spark sources can ignite the spraying vi-

cinity/environment.



Do not spray any liquid of unknown hazard potential. 

Unknown materials can create hazardous conditions.



Do not spray wallpaper stripper or boiling water. Spray 
only warm water (max. 55 ° C) without chemical addi-
tives. 



Wear additional protective equipment such as appro-
priate protective gloves and protective masks or respi-
rators when spraying or handling chemicals. 

Wearing 

protective equipment for the appropriate conditions re-
duces the exposure to hazardous substances.



Be aware of possible hazards from the spray material. 
Observe the information on drums/tanks/tins as well 
as manufacturer information of the spray material, in-
cluding the request to wear personal protective equip-
ment. 

The manufacturer's instructions are to be observed 

in order to reduce the risk of fire as well as injuries caused 
through toxins, carcinogens, etc.



Keep the plug of the mains cord and the trigger switch 
of the spray gun clear of paint and other fluids. Never 
hold the cord by its connectors to support it. 

Failure to 

follow the instruction can lead to electric shock.



Supervise children. 

This will ensure that children do not 

play with the fine-spray system.

Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

OBJ_BUCH-2024-005.book  Page 18  Wednesday, September 13, 2017  6:05 PM