Mitsubishi Electric MSZ-GF60VE - Инструкция по эксплуатации - Страница 5

En-4

 AUTO mode (Auto change over)

The unit selects the operation mode according to the difference between the 

room  temperature  and  the  set  temperature.  During  AUTO  mode,  the  unit 

changes  mode  (COOL↔HEAT)  when  the  room  temperature  is  2°C  away 

from the set temperature for more than 15 minutes.

Note: 

Auto Mode is not recommended if this indoor unit is connected to a MXZ 

type outdoor unit. When several indoor units are operated simultaneously, 

the  unit  may  not  be  able  to  switch  operation  mode  between  COOL  and 

HEAT. In this case, the indoor unit becomes standby mode (Refer to table 

of Operation indicator lamp).

 COOL mode

Enjoy cool air at your desired temperature. 

Note: 

Do not operate COOL mode at very low outside temperatures (less than 

-10°C).  Water  condensed  in  the  unit  may  drip  and  wet  or  damage  furni-

ture, etc.

  DRY mode

Dehumidify your room. The room may be cooled slightly. 

Temperature cannot be set during DRY mode.

  HEAT mode

Enjoy warm air at your desired temperature.

  FAN mode

Circulate the air in your room.

Note: 

After  COOL/DRY  mode  operation,  it  is  recommended  to  operate  in  the 

FAN mode to dry inside the indoor unit.

Operation indicator lamp

Emergency operation

When the remote controller cannot be used...

Emergency  operation  can  be  activated  by  pressing  the  emergency  operation 

switch (E.O.SW) on the indoor unit.

Each time the E.O.SW is pressed, the operation changes in 

the following order:

1

Press 

 to start the operation.

2

Press 

 to select operation mode. Each press 

changes mode in the following order:

3

Press 

 or 

 to set the temperature.

Each press raises or lowers the temperature by 1°C.

Press 

 to stop the operation.

•  The same setting is selected the next time by simply pressing

.

Auto restart function

If a power failure occurs or the main power is turned off during operation, “Auto 

restart  function”  automatically  starts  operation  in  the  same  mode  as  the  one 

set with the remote controller just before the shutoff of the main power. When 

timer is set, timer setting is cancelled and the unit starts operation when power 

is resumed.

If you do not want to use this function, please consult the service repre-

sentative because the setting of the unit needs to be changed.

S

ELECTING OPERATION MODES

Set temperature : 24°C

Fan speed : Medium

Horizontal vane : Auto

Emergency COOL

Emergency HEAT

Stop

Note:

The  fi rst  30  minutes  of  operation  is  test  run.  Temperature 

control does not work, and fan speed is set to High.

Note:

Multi system operation

Two or more indoor units can be operated by one outdoor unit. When several 

indoor  units  are  operated  simultaneously,  cooling  and  heating  operations 

cannot  be  done  at  the  same  time.  When  COOL  is  selected  with  one  unit  and 

HEAT  with  another  or  vice  versa,  the  unit  selected  last  goes  into  standby 

mode.

Operation indicator lamp

The operation indicator lamp shows the operation state of the unit.

Indication

Operation state

Room temperature

The unit is operating to reach the set 

temperature

About  2°C  or  more  

away from set tem-

perature

The room temperature is approach-

ing the set temperature

About 1 to 2°C from 

set temperature

Standby  mode  (only  during  multi 

system operation)

—

  Lighted 

  Blinking 

  Not lighted

 (AUTO)  (COOL) 

(DRY) 

(HEAT) 

(FAN)

JG79A927H01_en.indd   4

7/2/2014   11:44:06 AM